Abstract:Low-melting-point silicon-boron system alloys are promising for low-temperature reactive melt infiltration to reduce high-temperature damage to silicon carbide fibers during the densification of SiC/SiC composites. Meanwhile, the oxidation resistance of the alloys will have a large impact on the intrinsic oxidation resistance of the composite. Herein, three alloys, Si-14.88B-7Mo, Si-14.88B-7Ti, and Si-14.88B-7Cr, were fabricated to investigate the oxidation behavior in air at 1000-1400 °C. The results showed that the oxidation weight gains of the Si-B-Mo alloy after oxidation at 1400 °C for 100 h were 0.9 mg/cm, which were only 50 and 1.5% of those of Si-B-Ti and Si-B-Cr alloys, respectively. The excellent oxidation resistance of Si-B-Mo alloys at 1000-1400 °C was attributed to the formation of glassy-surface layers and the dense internal oxide layer. The dense oxide layer and the low solubility of Mo ions in SiO inhibit the volatilization of MoO and the oxidation reaction, reducing the oxidation rate of the Si-B-Mo alloy. The difference in the coefficients of thermal expansion for SiO and TiO led to penetrating cracks in the oxide layer of the Si-B-Ti alloy during cooling, thereby reducing the oxidation resistance. In addition, the rate of volatilization of CrO as CrO in an oxidation atmosphere above 1200 °C increased significantly in the Si-B-Cr alloy. The simultaneous volatilization of BO and CrO resulted in the formation of loose oxide layers in the CrB region of the Si-B-Cr alloy, leading to severe oxidation.

Improvement of Oxidation Resistance of a Mo-62Si-5B (at.%) Alloy at 1250 °C and 1350 °C Via an in Situ Pre-Formed SiO2 Fabricated by Spark Plasma Sintering

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Improvement of “pest” Resistance of MoSi2 Intermetallic Compound at 500 °C and 600 °C Via Addition of B Fabricated by Spark Plasma Sintering

Isothermal and Cyclic Oxidation Behaviours of MoSi2 with Additions of B at 1250 °C Prepared by Spark Plasma Sintering

Rapid Sintering Preparation and High Temperature Oxidation Behavior of MoSi2-B4C Composite Coating on Nb Alloy

Reaction synthesis of spark plasma sintered MoSi2-B4C coatings for oxidation protection of Nb alloy

Microstructural Evolution and Oxidation Behaviour of Mo-Si-B Coatings on an Nb-16Si-22Ti-7Cr-2Al-2Hf Alloy at 1250 °C Prepared by Spark Plasma Sintering

Preparation and enhanced oxidation behavior of microalloyed Mo5SiB2 alloy at 1300 °C

Microstructural Development and Oxidation Resistance of MSi2-type Multicomponent Silicide Coatings on Nb Alloys by Spark Plasma Sintering

Oxidation and Interdiffusion Behavior of Mo-Si-B Coating on Nb-Si Based Alloy Prepared by Spark Plasma Sintering

Oxidation Behavior of Zr-Y Alloyed Mo-Si-B Based Alloys

Microstructure and oxidation response of Mo-Si-B-ZrB 2 alloy at 900 °C: Effect of pre-oxidation treatment

Development of Mo(Si,Al)2-MoB Composite Coatings to Protect TZM Alloy Against Oxidation at 1400 °C

Microstructural Evolution and High-Temperature Oxidation Mechanisms of a Ti-Mo-Si Composite

Study on the Pre-Oxidation and Resulting Oxidation Mechanism and Kinetics of Mo-9Si-8B Alloy

Property and Oxidation Behaviours of (mo,cr)si2 + ZrO2 Composite Produced by Pressure-Less Sintering

In Situ Synthesis of (Mo,Cr)Si2 Composites by Spark Plasma Sintering

Plasma Oscillatory Pressure Sintering of Mo-9Si-8B Alloy with ZrB2 Addition

Oxidation Behavior of the Si-B-X (X = Mo, Cr, or Ti) Alloys in the Temperature Range of 1000–1400 °C

Oxidation Behavior and Microstructural Evolution of a Slurry Sintered Si-Mo Coating on Mo Alloy at 1650 °C

Microstructure and oxidation behavior of carbon fiber reinforced SiC composite (Cf/SiC) with Mo–57Si–10B oxidation protection coating