Abstract:Low-melting-point silicon-boron system alloys are promising for low-temperature reactive melt infiltration to reduce high-temperature damage to silicon carbide fibers during the densification of SiC/SiC composites. Meanwhile, the oxidation resistance of the alloys will have a large impact on the intrinsic oxidation resistance of the composite. Herein, three alloys, Si-14.88B-7Mo, Si-14.88B-7Ti, and Si-14.88B-7Cr, were fabricated to investigate the oxidation behavior in air at 1000-1400 °C. The results showed that the oxidation weight gains of the Si-B-Mo alloy after oxidation at 1400 °C for 100 h were 0.9 mg/cm, which were only 50 and 1.5% of those of Si-B-Ti and Si-B-Cr alloys, respectively. The excellent oxidation resistance of Si-B-Mo alloys at 1000-1400 °C was attributed to the formation of glassy-surface layers and the dense internal oxide layer. The dense oxide layer and the low solubility of Mo ions in SiO inhibit the volatilization of MoO and the oxidation reaction, reducing the oxidation rate of the Si-B-Mo alloy. The difference in the coefficients of thermal expansion for SiO and TiO led to penetrating cracks in the oxide layer of the Si-B-Ti alloy during cooling, thereby reducing the oxidation resistance. In addition, the rate of volatilization of CrO as CrO in an oxidation atmosphere above 1200 °C increased significantly in the Si-B-Cr alloy. The simultaneous volatilization of BO and CrO resulted in the formation of loose oxide layers in the CrB region of the Si-B-Cr alloy, leading to severe oxidation.

Development of Mo(Si,Al)2-MoB Composite Coatings to Protect TZM Alloy Against Oxidation at 1400 °C

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

High temperature oxidation behavior of MoSi2–Al2O3 composite coating on TZM alloy

Microstructure and oxidation resistance of Si-MoSi2 ceramic coating on TZM (Mo-0.5Ti-0.1Zr-0.02C) alloy at 1500 °C

Improving oxidation resistance of TZM alloy by deposited Si–MoSi2 composite coating with high silicon concentration

Oxidation Behavior of (Mo,Hf)Si2-Al2O3 Coating on Mo-Based Alloy at Elevated Temperature

Microstructure and Cyclic Oxidation Behavior of Hot-dip Aluminized Coating on TZM Alloy

Preparation and high‐temperature oxidation resistance of multilayer MoSi 2 /MoB coating by spent MoSi 2 ‐based materials

Fabrication of MoSi2 coatings on molybdenum and its high-temperature anti-oxidation properties

Microstructure evolution and growth mechanism of Si-MoSi2 composite coatings on TZM (Mo-0.5Ti-0.1Zr-0.02 C) alloy

Microstructure evolution and oxidation behavior of bi-layer CrAl-Mo coated Zircaloy-4 in steam at 1200 o C and 1300 o C

Microstructure and oxidation response of Mo-Si-B-ZrB 2 alloy at 900 °C: Effect of pre-oxidation treatment

Effect of Al content on 1200 °C steam oxidation behavior of Cr-based coatings on TZM alloy

Preparation and enhanced oxidation behavior of microalloyed Mo5SiB2 alloy at 1300 °C

Microstructure and high-temperature oxidation resistance of MoSi2-ZrO2 composite coatings for Niobium substrate

Oxidation-Resistant Coatings Based on High-Entropy Alloy (MoTaNbZrHf)SiB with Increased Silicon Content, Deposited by Magnetron Sputtering

Formation of MoSi2 and Si/MoSi2 coatings on TZM (Mo–0.5Ti–0.1Zr–0.02C) alloy by hot dip silicon-plating method

Oxidation Protection of High-Temperature Coatings on the Surface of Mo-Based Alloys—A Review

Oxidation Behavior of the Si-B-X (X = Mo, Cr, or Ti) Alloys in the Temperature Range of 1000–1400 °C

Recycling of MoSi2-based industrial solid wastes for the fabrication and high-temperature oxidation behavior of MoSi2–ZrSi2–SiC composite coating

A novel composite Si-Mo-Ti coating with Ti concentration gradient for Nb-Si based ultrahigh temperature alloy prepared by slurry sintering