Abstract:High-energy rechargeable lithium metal batteries (LMBs) have attracted significant attention recently. These batteries can be bulit using high areal-capacity (>4 mAh.cm(-2)) layered oxide cathodes and thin lithium (Li) metal anodes (<50 mu m in thickness), whose cycle performance are severely limited by the unregulated growth of Li particles having high surface areas, including dendrites and mossy Li. To improve the cycle performance of LMBs, many approaches have been developed in recent years to promote dendrite-free and dense Li electrodeposition, such as electrolyte engineering (for liquid cells), Li anode surface modification, three-dimensional current collector design, and using solid-state electrolytes. In addition to these heavily researched chemical-based approaches, applying external pressure to LMBs can also strongly impact the morphology of the electrochemically deposited Li particles due to the malleable nature of metallic Li and has been shown to improve the cycle performance. However, the relationship between the applied pressure, morphological evolution of the Li anode and the cycle performance has not been fully understood, especially in coin cells, which are widely used for LMB research. Here we report a custom-designed pressure applying/measurement device based on thin-film pressure sensors to realize real-time tracking of the pressure evolution in LMB coin cells. Our results show that moderate pressure is conducive to dense Li deposition and increases the cycle life, whereas excessive pressure causes Li inward-growth and the deformation of Li anode, which will impare the electrochemical performance of LMBs. Although these observations are made in coin cells, they could have important implications for pouch cells and solid-state batteries, both of which are commonly tested under pressure. The cycle performance of LMBs is significantly improved in both coin cells (under actual relevant conditions) and large pouch cells. A 5 Ah pouch-type LMB with a high energy density exceeding 380 Wh.kg(-1) could achieve stable cycling over 50 cycles under a stack pressure of similar to 1.2 MPa. It was also confirmed that the cell holders or clamps commonly used for coin cells can only exert a small amount of pressure, which is unlikely to exaggerate the cycle performance of the LMB coin cells. However, we do suggest that the electrochemical performance of LMBs should be reported along with the information on the applied pressure. This research practice will improve the consistency and quality of the reported data in the LMB research community and help unite the efforts to further improve the high energy density LMBs.

Effect of pressure on charge and discharge performance and expansion of ternary lithium battery

Experimental data simulating lithium battery charging and discharging tests under different external constraint pressure conditions

An investigation on expansion behavior of lithium ion battery based on the thermal-mechanical coupling model

Effect of external pressure and internal stress on battery performance and lifespan

Impact of Pressure Distribution and Magnitude on the Performance of Lithium Metal Anodes

Analysis on the effect of external press force on the performance of LiNi0.8Co0.1Mn0.1O2/Graphite large pouch cells

Pressure-Driven Interface Evolution in Solid-State Lithium Metal Batteries

Effect of explosion impact on the electrical performance and appearance of lithium-ion battery

Molecular Insights into the Structure and Property Variation of the Pressure-Induced Solid Electrolyte Interphase on a Lithium Metal Anode.

How Does External Pressure Shape Li Dendrites in Li Metal Batteries?

Deformation and Failure Properties of High-Ni Lithium-Ion Battery under Axial Loads

Performance of Lithium-Ion Pouch Cells with Silicon Composite Anodes under External Mechanical Pressure

Tracking Pressure Changes and Morphology Evolution of Lithium Metal Anodes

Effect of temperature on compression behavior of polypropylene separator used for Lithium-ion battery

Experimental and Numerical Study on Mechanical Deformation Characteristics of Lithium Iron Phosphate Pouch Battery Modules under Overcharge Conditions

Influences of compression on the mechanical behavior and electrochemical performances of separators for lithium ion batteries

Analysis of Pressure Characteristics of Ultra-High Specific Energy Lithium Metal Battery for Flying Electric Vehicles

State-of-Charge Dependence of Mechanical Response of Lithium-Ion Batteries: A Result of Internal Stress

Deformation and Failure of Lithium-Ion Batteries Treated As a Discrete Layered Structure

Synergistic Effect of Interface Layer and Mechanical Pressure for Advanced Li Metal Anodes

External Pressure Affecting Dendrite Growth and Dissolution in Lithium Metal Batteries During Cycles