Abstract:Perovskite is widely used as catalyst supports because of its flexible composition, good redox performance, and excellent thermal stability. However, the use of perovskite oxides as catalyst supports has two disadvantages: low surface area due to synthesizing the perovskite structure at high temperatures, and native perovskite surfaces preferentially have A-sites instead of catalytically active sites. On the other hand, interaction between the support and metal affects the size and valence state of noble metals. Therefore, perovskite oxides with different structures were prepared and were used to support Au catalysts, in order to obtain excellent catalytic activity and high stability. Specifically, stoichiometric LaMnO3 and nonstoichiometric LaMn1.2O3 perovskites were prepared by the ethylene glycol sol-gel method, and then the LaMnO3-AE oxide was prepared by treating LaMnO3 perovskite with dilute nitric acid. The perovskite-supported Au catalyst was prepared by the deposition precipitation method and its catalytic activity for CO oxidation was evaluated. Using X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and H-2 temperature-programmed reduction (H-2-TPR), it was found that LaMnO3 and LaMn1.2O3 perovskite carriers were beneficial for the dispersion of Au; however, the Au nanoparticle size significantly increased with increasing calcination temperature, indicating poor Au thermal stability. In contrast, LaMnO3 perovskite (LaMnO3-AE) etched by nitric acid is not conducive to dispersion of Au, but it is beneficial for improving the thermal stability of Au. Au was always maintained in the zero-valence state after calcination at different temperature. H-2-TPR results revealed that the reducibility of the catalysts changed largely after thermal treatment at high temperatures, and was mainly influenced by the agglomeration of Au nanoparticles. Although the reducibility of the Au/LaMnO3-AE catalyst calcined at 250 degrees C is lower than that of Au/LaMn1.2O3 and Au/LaMnO3 catalysts calcined at the same temperature, the former exhibited higher reducibility when the catalyst was calcined at high temperatures (500 and 900 degrees C). In the CO oxidation reaction, the catalytic activity of all the prepared catalysts decreased when the calcination temperature was increased from 250 to 500, 700, and 900 degrees C. However, the catalytic activity of the Au/LaMn1.2O3 catalyst was significantly higher than those of LaMnO3- and LaMnO3-AE-supported Au catalyst, when calcination temperature was below 500 degrees C, while the activity of the Au/LaMnO3-AE catalyst was significantly higher than those of the Au/LaMnO3 and Au/LaMn1.2O3 catalysts when the calcination temperature was more than 700 degrees C. As shown in characterization results, after the catalyst was calcined at high temperatures (700 and 900 degrees C), the Au nanoparticle size on the Au/LaMnO3-AE catalyst was lower than those on Au/LaMnO3 and Au/LaMn1.2O3 catalysts, leading to high reducibility and catalytic activity of the Au/LaMnO3-AE catalyst. The Au/LaMnO3-AE catalyst also exhibited high stability in CO oxidation. The catalytic activity of the Au/LaMnO3-AE catalyst can be maintained for 20 hat 130 degrees C.

Catalytic performance of rare earth nanometer materials LaMnO3+lambda

Structural Characterization and Co Oxidation Activity of Nanostructured Lamno3 Catalysts

Preparation Of Aromatic Aldehydes From Lignin Oxidation With A Perovskite-Type Catalyst

Catalytic Activity of Au Nanoparticles Supported on LaMnO 3 Perovskite with Different Composition and Structure

Effect of Different Reaction Conditions on Catalytic Activity of La(Mn, Fe)O3+lambda Catalyst for Methane Combustion

Effect of Preparation Conditions on Catalytic Activity of LaMnO3 on Oxidation of Carbon Black

LaMnO3-based Perovskite with In-Situ Exsolved Ni Nanoparticles: a Highly Active, Performance Stable and Coking Resistant Catalyst for CO2 Dry Reforming of CH4

Synthesis Of Nanostructure Lamno3 And Lacoo3 Catalysts And Their Catalytic Activity In Oxidation Reaction

Performance of Modified La Xsr1- Xmno3 Perovskite Catalysts for NH3 Oxidation: TPD, DFT, and Kinetic Studies.

Effect of Cu Doping on the Structure and Catalytic Activity of LaMnO_3 Catalyst

Selective Catalytic Reduction ofNOx by Methane over La(1-x)SrxMnO3 Perovskites

Lamno3 Perovskite Oxides Prepared by Different Methods for Catalytic Oxidation of Toluene

Effects of Preparation Methods on the Catalytic Performance of LaMn0.8Mg0.2O3 Perovskite for Methane Combustion

Influence of Partial Mn-substitution on Surface Oxygen Species of LaCoO3 Catalysts

Synthesis of La2O3/BaCO3 Nanocatalysts and Their Catalytic Performance

Effect of Jahn−Teller Distortion in La0.5Sr0.5MnO3 Cubes and Nanoparticles on the Catalytic Oxidation of CO and CH4

The High Activity and Stability of La0.5ba0.5mno3 Nanocubes in the Oxidation of Co and Ch4

Engineering the Microenvironment of Pd Nanoparticles on Porous MnOx Matrix to Improve Catalytic Toluene Combustion

Catalytic Behavior of Hydrothermally Synthesized La0.5Sr0.5MnO3 Single-Crystal Cubes in the Oxidation of CO and CH4

Controlled construction of Co<sub>3</sub>Mn<sub>1</sub> nanocrystals on one-dimensional ZnO surfaces for catalytic performance of CO oxidation

Improvement of CO Oxidation and CH4 Combustion by Pd and Pt Partial Substitution on LaMn0.5Cu0.5O3 Perovskite