BEAM POSITION MONITOR DESIGN FOR DIELECTRIC WAKEFIELD ACCELERATOR IN THz RANGE

Qiang Gao,Chunguang Jing,Jiaru Shi,Huaibi Chen,Wei Gai

2016-01-01

Abstract:Dielectric based collinear wakefield accelerator have been broadly selected for the THz accelerator due to its simplicity. In order to move the THz accelerators from the current exploratory research into the practical phase, certain common accelerator components are indispensable. Beam Position Monitor (BPM) is one of them. However, most of conventional BPM techniques are hardly scaled down to THz regime. Here we propose a BPM design which uses the dominant dipole mode excited in the dielectric wakefield accelerators to extract information of the beam position. INTRODUCTION Beam-driven wakefield accelerators are promising candidates for TeV class high energy colliders and for other applications like providing beam for compact FELs [1-2]. A very high accelerating gradient (GV/m level) can be achieved in wakefield accelerators [3]. To take advantage of the high gradient, wakefield accelerators are generally required to operate in THz regime (>0.1THz). Dielectric-based THz collinear wakefield accelerators (DWA) are preferred because of its simplicity. In order to realize the wakefield acceleration in a practical matter, one inevitable issue is the need to control Beam Breakup (BBU) which ensures the drive beam to be able to propagate until it has exhausted most of its energy. It has been shown in [2, 4] that single bunch BBU limits the distance over which the drive bunch can propagate in the dielectric lined waveguide before it begins losing electrons into the walls of the structure. A practical design of a DWA has been proposed (extended over 20 m and capable to ~80% energy extraction efficiency) in which BBU is controlled by employing BNS damping [2]. However, in order to achieve this goal of BBU control, a very tight tolerance on a straightness of the beam trajectory is applied. The beam position monitor (BPM) is a must to track the beam trajectory in particle accelerators. The conventional BPM techniques like the stripline and button BPMs are not suitable for the THz accelerators which has the beam pipe in the order of a few millimetres. The cavity BPM can be used in principle by choosing a higher order dipole mode, however, it will take the extra space of beaimline which has already been tight resulting from the BBU control lattice. In addition, the fabrication precision of a cavity BPM in THz may be prohibitive. Instead of using an extra BPM device, in this paper we present a new method to detect beam position for collinear wakefield accelerators using the TE11 like mode in the beampipe which is naturally converted from HE11 mode, the dominant dipole mode in a DWA structure. PRINCIPLE In a DWA structure (Note, we only discuss the cylindrical DWA in this paper. The drive bunch traverses along the structure geometrical centre, it will only excite the TM01 mode which is the fundamental-monopole mode to accelerate the trailing bunch. The dipole mode HEM11 will be excited when the particle has an offset to the centre. In the Fig.1, we assume that the particle coordinate in the vacuum region is (r0, θ0), which denotes the distance and azimuthal angle in the cylindrical coordinate. Figure 1. Cross section view of the dielectric accelerating structure (left). BPM coupler model in CST Microwave Studio (right). Based on the wakefield theory [5], particle will exchange the energy with the structure and radiate electromagnetic field. The radiation field can be decomposed as guided wave modes in the frequency domain. The peak gradient of each mode can be expressed as 1 2 1 a g q R E Q           (1) Where q is the charge, ω is the eigen-mode angular frequency, R over Q is the normalized shunt impedance along the particle trajectory for this mode, g  is the group velocity of the eigen-mode. For TM01 mode, this value is consistent and irrelevant to particle position. But for the dipole mode, this value is proportional to the particle offset to the center. The power extracted out at the end of dielectric-lined waveguide is [6]:   2 2 2 1 1 , 0 4 4 1 a g s g s L g E v R P q v t k Q                       (2) Where the s  is the power pulse length, which is determined by the waveguide length and group velocity. Proceedings of IPAC2016, Busan, Korea MOPMB037 06 Beam Instrumentation, Controls, Feedback and Operational Aspects T03 Beam Diagnostics and Instrumentation ISBN 978-3-95450-147-2 171 C op yr ig ht © 20 16 C C -B Y3. 0 an d by th e re sp ec tiv e au th or s If we take the attenuation and bunch charge density into consideration, we can get the power level as