Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

CFD-EDM Simulation of Discharged Catalyst by Acceleration Air Classification

Progress on agitated apparatus for polymer devolatilization and its CFD simulation

Air Acceleration Classification for the Enhancement of Spent Catalyst Activity Classification

Cfd-Dem Investigation of Particle Elutriation with Electrostatic Effects in Gas-Solid Fluidized Beds

CFD Simulation and Experiments of Dynamic Parameters in Gas–solid Fluidized Bed

CFD simulation of cross flow in multi-tubular fixed-bed reactor of industrial level

CFD–DEM Simulation of Gas–solid Reacting Flows in Fluid Catalytic Cracking (FCC) Process

Experimental and Numerical Simulation of Catalyst Deactivation Caused by Transient Turbulence in Gradient Flow Field

CFD-DEM Simulation of Flow and Mixing Behavior in Downers with Different Entrance Structures

Integrated Gas and Solid Model to Determine the Flow Performance in the SCR Reactor

CFD-DEM Simulation of Gas-Solid Reacting Flows in Catalytic Reactor

Developing an adaptive catalyst for an FCC reactor using a CFD RSM, CFD DPM, and CFD DDPM–EM approach

CFD-DEM Modeling of Rod-Like Particles in a Fluidized Bed with Complex Geometry

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Study on a Semi-Resolved CFD-DEM Method for Rod-Like Particles in a Gas-Solid Fluidized Bed

Cyclonic Gas Stripping Deoiling and Gas Flow Acceleration Classification for the Resource Utilization of Spent Catalysts in Residue Hydrotreating Process

Comparison of Two Lab Simulation Methods of Multiple Heavy Metal Contamination on FCC Catalysts

CFD-DEM simulation of particle coating process coupled with chemical reaction flow model

Study on the flow and collision characteristics of catalyst particles in FCC reactor

Dynamic Impacts of Catalyst Management on Self-fluidized Pump-Free Ebullated-Bed Reactor

CFD simulation of mass transfer in electrochemical reactor with mesh cathode for higher phenol degradation