Abstract:The anode substrates in the planar anode-supported solid oxide fuel cells (SOFC) were prepared by tape calendaring process, as well as the thin electrolyte films for increasing the power density of SOFCs at reduced operation temperature were fabricated by slurry-coating method. The minimization of co-firing temperature for anode and electrolyte layers was investigated by a novel three-step sintering technique in this paper. In order to obtain large three phase boundaries (TBP) at the electrolyte/anode interface, active anode layer was screen printed onto the anode substrate. Dense yttria stabitized zirconia (YSZ) thin films with a 10-15 mu m thickness on porous anode substrates were successfully fabricated by slurry-coating in an YSZ suspension. These three layers were co-fired together at 1300-1350 degrees C. The fuel cells with a diameter of 25 mm, fabricated by this co-firing technique show relatively high power density. The open circuit voltage (OCV) of 1.10 V was observed at 800 degrees C, the maximum power densities are 0.28, 0.51 and 0.95 W cm(-2), at 700, 750 and 800 degrees C, respectively. (C) 2008 Elsevier B.V. All rights reserved.

Optimization of Porous YSZ Substrate in the Tri-layer Structure Solid Oxide Fuel Cell

YSZ Thin Films Prepared by a Novel Powder Coating Process on Porous NiO-YSZ Cermet

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

High Performance Solid Oxide Fuel Cells Based on Tri-Layer Yttria-Stabilized Zirconia by Low Temperature Sintering Process

Microstructure Tailoring of the Nickel Oxide-Yttria-Stabilized Zirconia Hollow Fibers Toward High-Performance Microtubular Solid Oxide Fuel Cells

Fabrication and Evaluation of a Ni/La0.75Sr0.25Cr0.5Fe0.5O3−δ Co-Impregnated Yttria-Stabilized Zirconia Anode for Single-Chamber Solid Oxide Fuel Cells

Enhanced Performance of Solid Oxide Fuel Cell by Manipulating the Orientation of Cylindrical Pores in Anode Substrate

Fabrication of an Anode-Supported Yttria-Stabilized Zirconia Thin Film for Solid-Oxide Fuel Cells Via Wet Powder Spraying

Preparation of Tubular YSZ Electrolyte and Its Application in Solid Oxide Fuel Cells

Performance Evaluation of Thin Membranes Solid Oxide Fuel Cell Prepared by Pressure-Assisted Slurry-Casting

Fabrication and Evaluation of NiO/Y2O3-stabilized-ZrO2 Hollow Fibers for Anode-Supported Micro-Tubular Solid Oxide Fuel Cells

Preparation of Yttria Stabilized Zirconia Powders with a Glycine-Nitrate Process for Intermediate-Temperature Solid Oxide Fuel Cells

Thin Yttria-Stabilized Zirconia Electrolyte and Transition Layers Fabricated by Particle Suspension Spray

Preparation and Performance of YSZ Thin-Film by Centrifugal Deposition Technique

A Symmetrical Solid Oxide Fuel Cell Prepared by Dry-Pressing and Impregnating Methods

Infiltrated Porous YSZ As a Cathode Active Layer for Cathode-Supported Solid Oxide Fuel Cells

Fabrication and Performance Test of Solid Oxide Fuel Cells with Screen-Printed Yttria-Stabilized Zirconia Electrolyte Membranes

Microstructure tailoring of YSZ/Ni-YSZ dual-layer hollow fibers for micro-tubular solid oxide fuel cell application

Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell

Metal-Supported Solid Oxide Fuel Cells with a Simple Structure

Effect of Composite Pore-Former on the Fabrication and Performance of Anode-Supported Membranes for SOFCs