Abstract:It is discovered in this investigation that there exist two different failure modes and a special separation angle which is the demarcation point of the two different failure modes when FDM (Fused Deposition Modelling) 3D printing materials fail under a tensile load. In order to further understand the mechanical properties of FDM 3D printing materials and promote the use of FDM 3D printing materials, their tensile failure strengths at different printing angles and separation angles are measured and analysed theoretically. A new separate-modes of transversely isotropic theoretical failure model is established to predict the tensile failure strength and separation angle of FDM 3D printing PLA (polylactic acid) material based on the hypothesis of transverse isotropy and the classical separate-modes failure criterion. During this research, the tensile specimens designed according to the current test standard ISO (527-2-2012) for plastic-multi-purpose specimens are fabricated in 7 different printing angles (<math>0∘</math>, <math>15∘</math>, <math>30∘</math>, <math>45∘</math>, <math>60∘</math>, <math>75∘</math>, <math>90∘</math>) and three levels of printing layer thickness (0.1 mm, 0.2 mm, 0.3 mm). Experimental results show that the tensile failure strength increases with the increase of the printing angle or the decrease of the layer thickness. Meanwhile, inter-layer failure tends to occur when the printing angle is small and in-layer failure tends to occur when the printing angle is big. In comparison with the results predicted by the established theoretical model, all values of the Generalized-Relative-Root-Mean-Square Error are close to zero and the experimental separation angles are also between <math>45∘</math> and <math>60∘</math>. So the predictive capacity of the theoretical model is affirmed by experimental results.

Temperature and strain rate-dependent compression properties of 3D-printed PLA: an experimental and modeling analysis

Investigating the large strain compression properties of PLA parts manufactured by FDM using experiments and constitutive modeling

A Constitutive Model for Strain Hardening Behavior of Predeformed Amorphous Polymers: Incorporating Dissipative Dynamics of Molecular Orientation

Thermomechanical Constitutive Behaviour of 3D Printed Biomimetic Polymer Material under High Strain Rates

Thermo-Mechanical Behavior and Strain Rate Sensitivity of 3D-Printed Polylactic Acid (PLA) below Glass Transition Temperature (Tg)

Experimental and Numerical Investigation of 3D Printing PLA Origami Tubes under Quasi-Static Uniaxial Compression

Prediction of The Mechanical Behavior of Polylactic Acid Parts with Shape Memory Effect Fabricated by FDM

Strain Rate Dependent Mechanical Properties of 3D Printed Polymer Materials Using the DLP Technique

Mechanical properties of 3D printed polylactic acid elements: Experimental and numerical insights

Impact of strain rate on mechanical properties of polylatic acid fabricated by fusion deposition modeling

Temperature-compensated Constitutive Model of Fused Filament Fabrication 3D Printed PLA Materials with Full Extrusion Temperatures

Experimental and numerical study of orthotropic behavior of 3D printed polylactic acid by material extrusion

The effect of processing parameters on the mechanical characteristics of PLA produced by a 3D FFF printer

Orthotropic elastic behaviors and yield strength of fused deposition modeling materials: Theory and experiments

Experimental Analysis and Design of 3D-Printed Polymer Elliptical Tubes in Compression

Experimental analysis and optimization of mechanical properties of FDM-processed polylactic acid using Taguchi design of experiment

Effect of Printing Parameters on the Thermal and Mechanical Properties of 3D-Printed PLA and PETG, Using Fused Deposition Modeling

A method to predict the ultimate tensile strength of 3D printing polylactic acid (PLA) materials with different printing orientations

Compressive behaviors of 3D printed polypropylene-based composites at low and high strain rates

Tensile failure strength and separation angle of FDM 3D printing PLA material: Experimental and theoretical analyses

Effect of Printing Parameters on the Mechanical Properties of Parts Fabricated with Open-Source 3D Printers in PLA by Fused Deposition Modeling