Abstract:It is discovered in this investigation that there exist two different failure modes and a special separation angle which is the demarcation point of the two different failure modes when FDM (Fused Deposition Modelling) 3D printing materials fail under a tensile load. In order to further understand the mechanical properties of FDM 3D printing materials and promote the use of FDM 3D printing materials, their tensile failure strengths at different printing angles and separation angles are measured and analysed theoretically. A new separate-modes of transversely isotropic theoretical failure model is established to predict the tensile failure strength and separation angle of FDM 3D printing PLA (polylactic acid) material based on the hypothesis of transverse isotropy and the classical separate-modes failure criterion. During this research, the tensile specimens designed according to the current test standard ISO (527-2-2012) for plastic-multi-purpose specimens are fabricated in 7 different printing angles (<math>0∘</math>, <math>15∘</math>, <math>30∘</math>, <math>45∘</math>, <math>60∘</math>, <math>75∘</math>, <math>90∘</math>) and three levels of printing layer thickness (0.1 mm, 0.2 mm, 0.3 mm). Experimental results show that the tensile failure strength increases with the increase of the printing angle or the decrease of the layer thickness. Meanwhile, inter-layer failure tends to occur when the printing angle is small and in-layer failure tends to occur when the printing angle is big. In comparison with the results predicted by the established theoretical model, all values of the Generalized-Relative-Root-Mean-Square Error are close to zero and the experimental separation angles are also between <math>45∘</math> and <math>60∘</math>. So the predictive capacity of the theoretical model is affirmed by experimental results.

Orthotropic elastic behaviors and yield strength of fused deposition modeling materials: Theory and experiments

A method to predict the ultimate tensile strength of 3D printing polylactic acid (PLA) materials with different printing orientations

Experimental and numerical study of orthotropic behavior of 3D printed polylactic acid by material extrusion

DESIGN OF ELASTICALLY ISOTROPIC PLA LATTICE STRUCRURE IN FUSED FILAMENT FABRICATION CONSIDERING MATERIAL ANISOTROPY

A novel model to estimate the structural properties of PLA-FFF components along any non-orthogonal direction

Implementation of an elastoplastic constitutive model for 3D-printed materials fabricated by stereolithography

Micromechanical modeling and numerical homogenization calculation of effective stiffness of 3D printing PLA/CF composites

Elasto-Plastic Mechanical Modeling of Fused Deposition 3D Printing Materials

Prediction of The Mechanical Behavior of Polylactic Acid Parts with Shape Memory Effect Fabricated by FDM

Tensile failure strength and separation angle of FDM 3D printing PLA material: Experimental and theoretical analyses

The effect of processing parameters on the mechanical characteristics of PLA produced by a 3D FFF printer

Investigating the large strain compression properties of PLA parts manufactured by FDM using experiments and constitutive modeling

Investigation on the Elasto-Plastic Constitutive Equation of Parts Fabricated by Fused Deposition Modeling

Experimental analysis and optimization of mechanical properties of FDM-processed polylactic acid using Taguchi design of experiment

Numerical Homogenization Calculation of Effective Stiffness of Fused Deposition Modeling Printing Carbon Fiber Reinforced Polylactic Acid Composites

Mechanical properties of 3D printed polylactic acid elements: Experimental and numerical insights

Generalized models for unidirectional anisotropic properties of 3D printed polymers

A novel generalized stress invariant-based strength model for inter-layer failure of FFF 3D printing PLA material

Effects of Fused Deposition Modeling Process Parameters on Tensile, Dynamic Mechanical Properties of 3D Printed Polylactic Acid Materials

Isotropic and Anisotropic Elasticity and Yielding of 3D Printed Material

Effect of Printing Parameters on the Tensile Properties of 3D-Printed Polylactic Acid (PLA) Based on Fused Deposition Modeling