Study on seam tracing with arc-ultrasonic

Long-biao HE,Min-Sheng WU,Lu-ming LI,Xiang-yang DUAN

DOI: https://doi.org/10.3969/j.issn.1001-2303.2005.08.014

2005-01-01

Abstract:The arc-ultrasonic signal received by sonic emission probe is used for detecting seam tracing.The results show that the phase difference and the amplitude variation can be considered as the criteria of seam tracing.

What problem does this paper attempt to address?

Evaluation of Pipe Axial Defeat Through the Use of Ultrasonic Guided Wave and Matching Pursuit

ZHENG Guojun,TANG Zhifeng,WANG Youzhao,L(U) Fuzai

DOI: https://doi.org/10.3901/jme.2013.04.001

2013-01-01

Journal of Mechanical Engineering

Abstract:˖Ultrasonic guided wave technology shows a good prospect in the long distance and large-scale structure of the non-destructive testing and health monitoring, thanks to its advantages such as single-ended excitation, long propagation distance, 100% detection of cross section.Constrained by theory and instrumentation technology, ultrasonic guided wave is basically only used for defect screening, ultrasonic guided wave quantitative detection technology has not been widely studied and applied.Aiming at the quantitative analysis of defect size problem in guided wave inspection, it proposes a method based on matching pursuit for quantifying the severity of pipeline defect along axial direction.By analyzing the characteristics of the echo signal, the optimized dictionary is constructed to efficiently decompose the edge reflection components from defect reflection signal.The axial extent of defect can be then quantitatively evaluated by using obtained information.Algorithm validation experiments of finite element numerical simulation as well as detecting the artificial defects in the aluminum pipe by using MSGW magnetostrictive guided wave detector show that the algorithm of error is less than 5%.
Measurement of Leak Location in Buried Iron Water Pipe with Acoustic Emission and EMD

GU Xiao-hong,HOU Di-bo,ZHOU Ze-kui

DOI: https://doi.org/10.3785/j.issn.1008-973x.2006.07.001

2006-01-01

Abstract:A method based on empirical mode decomposition(EMD) and power feature extraction to locate the leak point was presented to overcome the disadvantage of location precision being low(affected by the noising and the propagation modes of sound) of direct cross-correlation method to pinpoint the leak point.This method based on data sampled by acoustic emission sensors,analyzed the direct cross-correlation affected by the noising and the propagation modes of sound,and decomposed the signal into a series of frequency bands,from which a few useful frequency bands were selected by power feature extraction,and then the leak point was determined by comparing the correlation coefficient.Simulation and experiments indicated that the method presented above eliminated the disadvantages of direct cross-correlation and improved the precision of location.
Research of Image Analyse Based on Multi Axis Ultrasonic - Dectect System

宋电子,周晓军,吴瑞明,何宇,王邦凯

DOI: https://doi.org/10.3969/j.issn.1001-3881.2004.10.101

2004-01-01

Abstract:The software module of image analysis was introduced for a new multi-axis-ultrasonic-detect system.The process of gaining ultrasonic image was explained.According to the particularity of ultrasonic image,applying ultrasonic image analysis based on digital image processing and pattern recognition,the recognition of defect in quality and quantity was realized.
Research on the Integrated Ultrasound and Eddy Automatic Inspection System of Seamless Steel Pipe

Lianghui Shang,Xiaojun Zhou,Siyuan Wu,Chenlong Yang

DOI: https://doi.org/10.4028/www.scientific.net/amm.101-102.100

2011-01-01

Applied Mechanics and Materials

Abstract:The existed semi-automatic ultrasound eddy current testing system is difficult to adapt to the situation of seamless steel tube detection requirements at present. This paper puts forward an ultrasonic eddy current synchronous auto-detection system. The principle of ultrasonic eddy current testing tube and the design of the ultrasonic eddy current probe frame are introduced. Software system uses ultrasonic and eddy current imaging at the same time, and ultrasonic testing’s results can be displayed by A+B+C combination imaging. The quasi three-dimensional imaging system can offer more convenient methods to detect personnel. Experimental results verify the feasibility of the system.
Study on identifying seam deviation information based on high speed rotating arc welding sensor

JIA Jian-ping,ZHANG Hua,YE Jian-xiong

DOI: https://doi.org/10.3969/j.issn.1000-9787.2007.08.016

2007-01-01

Abstract:The high speed rotating arc welding sensor drived by motor with hollow shaft is used in seam tracking system.It is used in seam tracking system and studied both at home and abroad.The structure and working theory of the arc sensor are introduced.The method of identifying signals of the seam deviation by the characteristic harmonic detection method is expounded.Tracking experiment of MIG on V shape welding groove is made with this method,and the experiment result validates the validity of this method.
A magnetic-control arc sensor for seam-tracking

HONG Bo,WEI Fuli,LAI Xin,PAN Jiluan,YIN Li

DOI: https://doi.org/10.3321/j.issn:0253-360X.2008.05.001

2008-01-01

Abstract:In order to solve the problems of abrading easily,loud noise and low stability of the mechanical arc sensor,a new method of seam-tracking with appending magnetic-control welding arc technology was presented and its basic principle was discussed.Based on the eleetromagnetic fields theory and magnetic-control law,the relationship of parameters was also analyzed.To obtain signals of welding current by Hall sensor,the Butterworth filter hardware filtering and the current of signal software handling method with wavelet analysis methods was utilized. The measured current signals of such three methods as magnetic-control swingarc,without magnetic field and mechanical rotatable-arc were analyzed,respectively,and the effective intorral twice romove extreme integral contrast method was used to extract actual seam deviation information.Results of these tests show that the magnetic-control arc sensor for seam tracking correct feasible can achieve good effect in tracing control and provide a potential direetion for the current seam-tracking technology.
Study of Arc-Ultrasonic Excitation and Its Characteristics

WU Minsheng,DUAN Xiangyang,LI Luming,SUN Diqing

DOI: https://doi.org/10.3321/j.issn:1000-0054.1999.06.031

1999-01-01

Abstract:In order to study the potential application for improving the crystallization of molten metal and for automatic seam tracking by using the welding arc, a working principle of the arc excited ultrasonic emission was introduced. For arc ultrasonic excitation, both the continuous and the pulse signal was separately applied to the test system including a conventional arc welding circuit. The spectrum, amplitude, phase shift and the acoustic velocity of the arc ultrasonic were detected and recorded in the welding process. The acoustic resonant phenomenon shows the selective frequency response of the arc ultrasonic. It may be significant for the manufacturing and the material engineering that arc or plasma could function not only as a thermal source, but also as a mechanism of the ultrasonic emission.
Seam tracking system with leading magneticcontrol arc sensor

HONG Bo,LAI Xin,WEI Fu-li,PAN Ji-luan,YIN Li,QU Yue-bo

DOI: https://doi.org/10.3969/j.issn.1000-9787.2008.05.031

2008-01-01

Abstract:Aimed at some problems of the mechanical arc sensor for seam-tracking,the magnetic-control welding arc technology is applied to seam tracleking,a new type magnetic-control arc sensor and a system structure with two sets of crossed slides are designed.The Butterworth filter and RCπ filter are adopted.The effective region and remove extreme integral contrast method is used to seek the errorinformation of the seam.The effectiveness of the system is verified by practical seam tracking experiment.
Seam Tracking System Based on Magnetic-Control Arc Sensor

HONG Bo,LAI Xin,WEI Fu-li,PAN Ji-luan,YIN Li

DOI: https://doi.org/10.3969/j.issn.1004-1699.2008.05.037

2008-01-01

Abstract:In order to solve some problems of the sensor for seam-tracking,applied the magnetic-control welding arc technology,developed a new type magnetic-control arc sensor,it's basic principle was analyzed,and mathematic model was built,the main parameters were analyzed,that provided academic foundation for the application of the magnetic-control arc sensor.A seam tracking system was designed,the sensor part and the real welding part were independent,that expanded it's use scope,Smith predicator was used to eliminate the influence of time-delay.In the aspect of signal processing,the Butterworth filter and RCπ filter were adopt,and achieved good effect;the effective region and remove extreme integral contrast method was used to seek the information of the seam.At last,the effectiveness of the system was verified by practical seam tracking experiment.
The Seam Tracking System for Submerged Arc Welding

Hua Zhang,Xuelei Ding,Maohua Chen,Benqi Da,Chunhua Zou

DOI: https://doi.org/10.1007/978-3-540-44415-2_9

2004-01-01

Abstract:The structure and the principle of seam tracking for submerged arc welding were introduced in this paper. The method of seam recognition with computer vision was mainly researched when the environmental light was changed. Intelligent control system for seam tracking has been realized by using a self-modulated fuzzy control set. The system was tested on the producing of spiral submerged arc welded pipe for outside-welding and the primary results were obtained.
Application Research on Ultrasonic Phased Array Technology in Weld Seam Inspection

Haixing Zhang

DOI: https://doi.org/10.1088/1742-6596/1601/4/042041

2020-07-01

Journal of Physics: Conference Series

Abstract:Abstract Welding seams are prone to safety accidents and failures during actual operation, which has an adverse effect on the economic benefits of the enterprise. When using traditional ultrasonic inspection methods to inspect the pipe butt welds, the staff needs to use the inspection probe to move as needed, which makes the inspection process difficult to operate and is greatly affected by human factors. The beam of conventional ultrasound cannot be deflected and focused. It is difficult to detect parts with complex geometric shapes and large anisotropic welds. Ultrasonic phased array is a new type of non-destructive testing method, which makes up for the limitations of conventional ultrasonic testing, and has great advantages compared with conventional ultrasound. Therefore, in order to reduce the misjudgment of defects caused by humans, this paper studies the application method of ultrasonic phased array technology in weld inspection, discusses the principles and characteristics of ultrasonic phased array inspection technology in nondestructive testing, and the defects were tested. The test results show that the phased array technology can effectively detect weld defects.
Seam Tracking Technology Based on Low-Frequency Rotatable Arc Sensor

QU Yue-bo,HONG Bo,PAN Ji-luan,YIN Yi,YUAN Can,HUANG Jun

DOI: https://doi.org/10.3969/j.issn.1001-2303.2005.04.014

2005-01-01

Abstract:This paper introduces a seam tracking technology based on a low-frequency rotatable arc sensor by means of adjusting the rotating radius of the arc sensor and modifying the eccentricity outfit,then adjusting the judge period and the sampling position and the number of the sampling,as well as dealing with the sampling current signal by minimum filtering value.The experiment proves that it has the advantage of reliable control and good seam tracking.
Application of Ultrasonic Sensor in Automatical Welding of Right-Angle Welding Seam

王英鸽,毛志伟,周少玲,张华

DOI: https://doi.org/10.3969/j.issn.1000-9787.2009.05.036

2009-01-01

Abstract:During the process of welding the lattice-shaped welding seam in the hall,the environment information around the welding seam can not be obtained totally only by the arc sensor.It is difficult to weld the right-angle seam automatically.A method of welding the right-angle seam automatically is designed,in which the obstacle is found by the ultrasonic sensor using its range finding principle instead of the touch sensor;and the deviation is gained by the arc sensor.With the reasonable control to the robot,the welding of the right-angle welding seam with seam automatic tracking can be finished.
Study on arc-ultrasonic welding technology

Min-Sheng WU,Long-biao HE,Lu-ming LI,Hong-wei HAO

DOI: https://doi.org/10.3321/j.issn:0253-360X.2005.06.011

2005-01-01

Abstract:The results of experiments with carbon steel, low temperature steel and titanium alloy showed that arc-ultrasonic refined the grains of the joint with the action of mass transmission and heat transmission during the welding process. And the impact ductility and fatigue life of the welded joint were improved by arc-ultrasonic, and at the same time, it was proved that the distribution of residual stress in weld zone was improved by arc-ultrasonic welding through the test of orifice method and megneto-mechanical effect. All the results showed the extensive application prospect of arc-ultrasonic, the universal adscititious ultrasonic field welding technology.
Study on DC4 Digital Ultrasonic Multi-wave Train Axle Detector

WANG Bing-tuan,FENG Yong-ge,CHENG Zheng-wei,MA Tian-lang,WANG Di,CHEN Li-cheng

DOI: https://doi.org/10.3321/j.issn:1001-8360.2005.03.020

2005-01-01

Abstract:According to the theory of the multi-wave seismic exploration, and due to the fact that the ultrasonic multi-wave metal detector cannot locate a crack and detect its, size and shape, this article studies the principle and characteristics of the ultrasonic multi-wave metal detector and also the 3-heft energy-exchange instrument in match with the ultrasonic multi-wave metal detector. The results demonstrate substantive achievement.
Signal Analysis of Ultrasonic C-Scan Testing for Multi-layer Welding Structure

Zheng Wang,Yiwei Shi,Jing Liang

2008-01-01

Abstract:：：： The multi-layer welding structure is a kind of important weld component used in modern aviation industry. In order to control the quality of the i nner welds, the method of ultrasonic immersion testing with focusing probe has been performed in this study. Some testing signals displayed in the screen are overlapping signals composed by the echoes with different propagation routes in the multi-layer welding structure. I n this paper, a method is given to recognize the valid signal basing on the analysis of sound routes. Computer simulation and a series of experiments are performed to prove the validit y of the method.
Research on feature point detection of discontinuity welding seam

XU Qing-rong,ZHANG Hua,YE Yan-hui,CHENG Wei-de

DOI: https://doi.org/10.3969/j.issn.1000-9787.2010.05.009

2010-01-01

Abstract:Some drainage holes at the bottom of hall in shipbuilding form discontinuity welding seams,which directly influence welding speed.In order to extract the characteristic signal of drainage holes,the welding current signal is extracted by the rotating arc sensor,the image of the welding seam information is extracted by the laser sensor.The experimental results show that the two sensors can meet the demand.The startpoint of the drainage holes were detected by the the rotating arc sensor and the endpoint by the vision sensor which controlled the pose of the robot simultaneously.
Seam tracking for space position based on rotating arc sensor

熊震宇,张华,潘际銮

DOI: https://doi.org/10.3321/j.issn:0253-360X.2003.05.010

2003-01-01

Abstract:The seam tracking system is introduced, where the rotating arc sensor drived with hollow axle motor is used, the teaching arc welding robot is used as controlling object. Based upon the signal processing method for the real state on the rotating arc sensor, the methods of seam recognition for space position such as flat position, horizontal position and vertical position are studied. A fuzzy control approach is utilized for designing the welding seam tracking system, which is successfully applied to seam tracking for above positions and will increase greatly the automatization of teaching welding robot.
Research on visual technology of trajectory tracking for robotic welding

Li WANG,Sheng-hua WANG,Dong DU

DOI: https://doi.org/10.3969/j.issn.1001-2303.2009.04.006

2009-01-01

Abstract:Aim at seam tracking methods for robotic welding with their limits and disadvantages in applications,that is the conventional active vision methods have difficulties to recognize structure without obvious geometric feature.Neither are the passive vision methods appropriate because of tense dependence on grey-level gradient characteristics.According to the analysis of current application of seam tracking technology,two methods based on the approach of using grain features are proposed,including the grain feature matching method and the grain segmentation method.Experiments have proved the feasibility and the adaptability of the generated seam image processing algorithm.The presented methods provide new possible solutions for seam tracking of multi-pass/multi-layer robotic arc welding.

Study on seam tracing with arc-ultrasonic

Evaluation of Pipe Axial Defeat Through the Use of Ultrasonic Guided Wave and Matching Pursuit

Measurement of Leak Location in Buried Iron Water Pipe with Acoustic Emission and EMD

Research of Image Analyse Based on Multi Axis Ultrasonic - Dectect System

Research on the Integrated Ultrasound and Eddy Automatic Inspection System of Seamless Steel Pipe

Study on identifying seam deviation information based on high speed rotating arc welding sensor

A magnetic-control arc sensor for seam-tracking

Study of Arc-Ultrasonic Excitation and Its Characteristics

Seam tracking system with leading magneticcontrol arc sensor

Seam Tracking System Based on Magnetic-Control Arc Sensor

The Seam Tracking System for Submerged Arc Welding

Application Research on Ultrasonic Phased Array Technology in Weld Seam Inspection

Seam Tracking Technology Based on Low-Frequency Rotatable Arc Sensor

Application of Ultrasonic Sensor in Automatical Welding of Right-Angle Welding Seam

Study on arc-ultrasonic welding technology

Study on DC4 Digital Ultrasonic Multi-wave Train Axle Detector

Signal Analysis of Ultrasonic C-Scan Testing for Multi-layer Welding Structure

Research on feature point detection of discontinuity welding seam

Seam tracking for space position based on rotating arc sensor

Research on visual technology of trajectory tracking for robotic welding