Abstract:Square-small holes are used as a critical feature in the fields of aerospace, machine-tooling, automation, and mechanical component construction. Electrochemical drilling (EC-drilling) is a promising approach for manufacturing square-small holes. However, the distribution of flow field in the inter-electrode gap (IEG) becomes non-uniform because of the unique structure of the square-cross-section tubular tool, leading to the accumulation of electrolytic by-products in the IEG. Consequently, both shape accuracy and machining efficiency are reduced. This paper proposes an EC-drilling process with workpiece vibration, in which low-frequency vibration is applied to the workpiece and the size of the frontal IEG is periodically altered. This approach can improve the flow field distribution and eliminate constant low flow velocity zones, resulting in enhanced mass transfer in the IEG. A 3D computational fluid dynamics (CFD) model includes discrete phase was developed to analyze the characteristics of the flow field and elucidate the enhancement mechanism of workpiece vibration in the transfer process. Simulation results revealed that a pulsating electrolyte flow field was produced in both frontal and side IEG induced by workpiece vibration, and that high flow velocity zones were generated alternately in frontal IEG and side IEG. With minimum frontal IEG, there was a high flow velocity in frontal IEG, with parcels (each parcel contains 205 particles) being transported smoothly from frontal IEG to the side IEG. High flow velocity switched to the side IEG when frontal IEG was maximum, and parcels that accumulated in the side IEG were easily removed. With the workpiece vibration process repeated, the parcel transfer process in the IEG was enhanced and the number of parcels accumulating in the IEG significantly reduced. The enhancement of workpiece vibration on the machining of square-small hole was verified by experiments, reflected as enhancement in both the surface quality and shape accuracy of square-small holes. Increasing both the vibration amplitude and frequency enhanced the removal rate of electrolytic by-products, thereby improving machining quality. Machining quality was further improved using a high pulse frequency and low pulse duty cycle. With appropriate parameters, the maximum cathode feed rate reached 1.44 mm/min, 2.4 times that previously reported, and the width and corner radius of the square-small hole was 1.16 mm ± 0.003 mm and 149 μm, respectively, with a surface roughness of 0.54 μm on the sidewall of the square-small hole.

Research on Small-hole Manufacturing Process through Electrochemical Machining with Side-insulated Tool Electrode

Study on Micro-hole Electrochemical Machining Process with Sidewall-insulated Tool Electrode

Multiphysics Research on Electrochemical Machining of Micro Holes with Internal Features

A study on wire electrochemical micromachining for fabrication of microgrooves

Research on Electrochemical Machining Technology of Deep Small Hole using Suction Electrode

Research on Ecm Process of Micro Holes with Internal Features

Electrochemical Machining of Hole Structures by Using Superhydrophobic Tube Electrode

Experimental Study on Micro Electrochemical Machining with Hydrophobic Side Insulation Electrode

Research on Side-Insulation of Tool Electrode for Micro Electrochemical Machining

Analysis of Multi-Physics Coupling of Small Holes in GH4169 Alloy by Electrolytic Processing of Tube Electrodes

Novel Structure Of A Sidewall-Insulated Hollow Electrode For Micro Electrochemical Machining

Electrochemical micro-machining of high aspect ratio micro-tools with a reverse conical shape tip using electrolyte liquid membrane

Wire Electrochemical Machining with Pulsating Radial Electrolyte Supply and Preparation of Its Tube Electrode with Micro-Holes

Effect of ultrasonic assisted EDM based on horizontal vibration on deep and small hole machining

Performance improvement of high-speed EDM and ECM combined process by using a helical tube electrode with matched internal and external flushing

On electrochemical machining with an interelectrode slit for a partially insulating cathode

Enhancement mechanism of electrochemical drilling square-small holes with workpiece vibration

Ultrasonically assisted electrochemical micro drilling with sidewall-insulated electrode

Side-Insulation of Tool Electrode and Application in Micro ECM

Research On Micro Electrode Fabrication Based On Ecm

Theoretical and experimental study on micro ultrasonic-assisted electrochemical drilling with high speed electrode