Abstract:Square-small holes are used as a critical feature in the fields of aerospace, machine-tooling, automation, and mechanical component construction. Electrochemical drilling (EC-drilling) is a promising approach for manufacturing square-small holes. However, the distribution of flow field in the inter-electrode gap (IEG) becomes non-uniform because of the unique structure of the square-cross-section tubular tool, leading to the accumulation of electrolytic by-products in the IEG. Consequently, both shape accuracy and machining efficiency are reduced. This paper proposes an EC-drilling process with workpiece vibration, in which low-frequency vibration is applied to the workpiece and the size of the frontal IEG is periodically altered. This approach can improve the flow field distribution and eliminate constant low flow velocity zones, resulting in enhanced mass transfer in the IEG. A 3D computational fluid dynamics (CFD) model includes discrete phase was developed to analyze the characteristics of the flow field and elucidate the enhancement mechanism of workpiece vibration in the transfer process. Simulation results revealed that a pulsating electrolyte flow field was produced in both frontal and side IEG induced by workpiece vibration, and that high flow velocity zones were generated alternately in frontal IEG and side IEG. With minimum frontal IEG, there was a high flow velocity in frontal IEG, with parcels (each parcel contains 205 particles) being transported smoothly from frontal IEG to the side IEG. High flow velocity switched to the side IEG when frontal IEG was maximum, and parcels that accumulated in the side IEG were easily removed. With the workpiece vibration process repeated, the parcel transfer process in the IEG was enhanced and the number of parcels accumulating in the IEG significantly reduced. The enhancement of workpiece vibration on the machining of square-small hole was verified by experiments, reflected as enhancement in both the surface quality and shape accuracy of square-small holes. Increasing both the vibration amplitude and frequency enhanced the removal rate of electrolytic by-products, thereby improving machining quality. Machining quality was further improved using a high pulse frequency and low pulse duty cycle. With appropriate parameters, the maximum cathode feed rate reached 1.44 mm/min, 2.4 times that previously reported, and the width and corner radius of the square-small hole was 1.16 mm ± 0.003 mm and 149 μm, respectively, with a surface roughness of 0.54 μm on the sidewall of the square-small hole.

Theoretical and experimental study on micro ultrasonic-assisted electrochemical drilling with high speed electrode

Simulation and Experimental Study on Micro Electrochemical Drilling with Ultra Short Pulse Voltage by Using High-speed Spiral Electrode

Simulation and Experimental Study on Ultrasonic Assisted Micro Drilling of Stainless Steel

A Novel Micro-Edm Method to Improve Microhole Machining Performances Using Ultrasonic Circular Vibration (UCV) Electrode

Experimental Research of High-Quality Drilling Based on Ultrasonic Vibration-Assisted Machining

Experimental investigation on cavitation effect and surface quality of ultrasonic-assisted micro-hole drilling

A study on ultrasonic-assisted micro-EDM of titanium alloy

Improvement of ultrasonic cavitation and pumping effect in microhole EDM

An Experimental Investigation of Enhancement Surface Quality of Micro-holes for Be-Cu Alloys Using Micro-EDM with Multi-diameter Electrode and Different Dielectrics

Electrochemical Drilling of Micro Holes with Flatted Electrode

Ultrasonic Cavitation and Vibration Hybrid-Assisted Micro-Drilling of Stainless Steel

Ultrasonic-assisted Micro-Hole Machining Research and Parameter Optimization Experiment

Research on an ultrasonic vibration assisted electrical discharge machining technology of micro deep hole with high aspect ratio

Experimental research and multi-objective optimization of ultrasonic vibration–assisted EDM for Ti6Al4V micro-holes

Enhancement mechanism of electrochemical drilling square-small holes with workpiece vibration

Ultrasonically assisted electrochemical micro drilling with sidewall-insulated electrode

Effects of Ultrasonic Vibration on Machining Accuracy in Drilling

Study on machining characteristics of magnetic field assisted micro-EDM with ultrasonic vibration of workpiece

Improving surface integrity of micro-holes in ECDM using ultrahigh-speed rotary of tool cathode and non-water-based electrolyte

Effect of ultrasonic assisted EDM based on horizontal vibration on deep and small hole machining

Dynamic chip formation of ultrasonic-assisted micro-drilling on AISI 4340 steel