Abstract:To improve the combination of graphite and copper, the friction and wear of a graphite/copper composite with a high content of graphite (50 wt %), copper-coated graphite were used to modify it. To observe the distribution law of each phase in the material and the change of composite surface structure after the friction and wear experiment, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the micro-structure, friction film, debris, and friction cross section of the composites. The results show that the large particle size of copper-coated graphite is anisotropic in the material, which helps to form a friction film with a high graphite content on the contact surface. TEM images of the friction film and debris directly reflect the structure changes of graphite and copper during friction; under normal load and shear force, interlamellar detachment and interlamellar fracture of graphite occur, and its edge is folded and crimped, resulting in the loss of an ordered state in some regions, which results in the instability of crystal lattice and the transition from an ordered to disordered state of graphite, resulting in the (002) halo ring in FFT results. Severe plastic deformation and oxidation reactions occur in copper, and copper oxides are formed, forming a high-strength and smooth oxide film in the metal-rich area and improving the wear resistance of the material. TEM images of the friction section directly show that an inverted triangular deformation zone is formed on the surface of the sample after friction and wear experiments. The edge of the deformation zone is stepped, consisting of a drag zone and an accumulation zone, and the surface of the contact zone is covered by a carbon film.

Tribological Behaviors of Graphite Sliding Against Cemented Carbide in Cacl2 Solution

Tribological Performances of Ti(C,N)-based Cermets with Different Graphite Contents in Dry Sliding Condition

Ultralow Friction Between Cemented Carbide and Graphite in Water Using Three-Step Ring-on-ring Friction Test

Frictional performance of surface-textured phenolic resin-impregnated graphite materials under water lubrication

Tribological Behavior of Cu-15Ni-8Sn/graphite under Sea Water, Distilled Water and Dry-Sliding Conditions

Wear Behavior and Self Tribofilm Formation of Hot-Pressed Al2O3/TiC/CaF2 Ceramic Composites Sliding Against Cemented Carbide

Influence of a Carbon-Based Tribofilm Induced by the Friction Temperature on the Tribological Properties of Impregnated Graphite Sliding Against a Cemented Carbide

Tribological behaviors of graphite/epoxy two-phase composite coatings

On the tribological behaviors of Cu matrix composites with different Cu-coated graphite content

Dry Wear Behaviors of Graphite/cermet Self-Lubricating Composite under Different Sliding Conditions and Simulation of Temperature Field

Wear Mechanism and Three-phase Synergistic Effect of Self-mated SiC/Si/Graphite Composites in Unlubricated Sliding

TRIBOLOGY PROPERTIES OF C/C COMPOSITES AND GRAPHITE AT NON-LUBRICATION WEAR ENVIRONMENT

Tribological Behavior of Textured Cemented Carbide Filled with Solid Lubricants in Dry Sliding with Titanium Alloys

Friction Characteristics of Impregnated and Non-Impregnated Graphite Against Cemented Carbide under Water Lubrication

The Effect of C/C Composites Characteristic on Sliding Friction and Wear Behavior

Effect of Graphitization Degree on 2.5D C/C Composite's Tribological Properties on Low Energy

Effect of Graphite Size on the Tribological Behavior of Ti (C, N)-based Cermets Self-Mated Wear Pairs

Tribological Performances of Diamond Film and Graphite/diamond Composite Film

Intuitive Analysis of the Microtribological Behavior of Copper-Coated Graphite–Graphite/Cu Composites with High Graphite Contents

Preparation and Tribological Properties of Graphene-Based Coatings on Tungsten Carbide

Tribological Behavior of Cu Matrix Composites Containing Graphite and Tungsten Disulfide