Abstract:TiC bonded diamond composites were prepared from a mixture of Ti, graphite, and diamond powders as raw materials, with Si as sintering additives, through high-temperature and high-pressure (HTHP) technology. The reaction between Ti and graphite under 4.5–5 GPa pressure and 1.7–2.3 kW output power can produce TiC as the main phase. The diamond particles are surrounded by TiC, and the interface is firmly bonded. The coefficient of friction (COF) of TiC–diamond composites with POM and PP balls decreases with increasing load for a specific friction velocity. However, the COF of TiC–diamond composites with agate, Cu and Al balls increases with the rising load because of the enhanced adhesive wear effect. The COF of PP, Cu and Al balls slightly increases with the increase in friction velocity at a certain load. SEM results show that the surface of agate balls has rough, pear-shaped grooves and shallow scratches. The scratches on the surface of POM balls are wrinkled. The PP balls have pear-shaped groove scratches on their wear surfaces. The wear mechanism of TiC–diamond composites with Cu ball pairs is primarily adhesive wear. The abrasion of TiC–diamond composites with Cu ball pairs remains almost unchanged as the load increases. However, the depth and width of the pear-shaped grooves on the wear surface of TiC–diamond composites are significantly increased. This phenomenon may be attributed to the high rotational speed, which helps to remove the residual abrasive debris from the friction grooves. As a result, there is a decrease in both the depth and width of the pear-shaped grooves, leading to a smoother overall surface. The wear mechanism of TiC–diamond composites with Al ball pairs is abrasive wear, which increases with an increasing load. When the load is constant, as the speed increases, the wear morphology of TiC–diamond composites with Al ball pairs transitions from rough to smooth and then back to rough again. This phenomenon may be attributed to the wear mechanism at low speeds being groove wear and adhesive wear. As the speed increases, the wear particles are more easily removed from the wear track, leading to a reduction in abrasiveness. As the speed increases, the wear surface becomes roughened by a combination of grooves and dispersed wear debris. This can be attributed to the increased dynamic interaction between surfaces caused by higher speed, resulting in a combination of abrasive and adhesive wear. In addition, Cu and Al ball wear debris appeared as irregular particles that permeated and adhered to the surface of the TiC phase among the diamond particles. The results suggest that TiC–diamond composites are a very promising friction material.

Tribological Performances of Diamond Film and Graphite/diamond Composite Film

Tribological Properties of Diamond Films and Graphite/diamond Composite Films with Dry Friction

A Comparative Investigation of the Tribological Behavior and Wear Mechanism of Bronze-graphite Composite under Dry- and Water-lubricated Sliding Against Steel

Microstructure and Tribological Performance of Self-Lubricating Diamond/tetrahedral Amorphous Carbon Composite Film

Tribological Properties of Al2O3/Graphite-Al2O3 Laminated Composites under Water Lubrication Conditions

Frictional performance of surface-textured phenolic resin-impregnated graphite materials under water lubrication

Tribological Behavior of Diamond-Like Carbon Film with Different Tribo-Pairs: A Size Effect Study

Study on tribology and cutting performance of boron doped diamond composite coated tool

In Situ Synthesis and Tribological Characterization of TiC–Diamond Composites: Effect of the Counterface Material on Wear Rate and Mechanism

Tribological Properties of Si-Doped Graphite-Like Amorphous Carbon Film of PEEK Rubbing with Different Counterparts in SBF Medium

Study on the lubrication film formation and characteristics of different graphite seal composites

Friction and wear characteristics of synthetic diamond and graphene-filled polyether ether ketone composites

Tribological performance of Graphene/Carbon nanotube hybrid reinforced Al2O3 composites

Comparing the tribological behavior of polycrystalline diamonds against steel GCr15 and ceramic Si 3 N 4 : friction and wear

Tribological Properties of EP Composites Reinforced with Short Glass Fiber, Graphite, PTFE and B4C Under Oil Lubrication

Friction and wear behavior of diamond film with adjustable grain size against silicon carbide in different tribological tests

Enhancement of Tribological Properties in Siliconized Graphite Via Hierarchically Hybrid SiC/C Composite

Investigation of the Mechanical and Tribological Properties of Diamond-Like Carbon Films on YG8 and High-Speed Steel Substrates with W Buffer Layers

A study of the wear mechanism of diamond-like carbon films

Tribological behaviors of Ag−graphite composites reinforced with spherical graphite

Surface analysis of iron-based self-lubricating composite under oil lubrication