Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Quasi-static tensile test of thick acrylic sheets at different temperatures

Experimental Study of Mechanical Properties of CFRP under Different Strain Rates and Temperatures

Temperature Effect on the Mechanical Behavior of Acrylic Polymers under Quasi-static and Dynamic Loading

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Investigation of Effect of Temperature and Strain Rate on Mechanical Properties of Underfill Material by Use of Microtensile Specimens

Time–temperature Correlations of Amorphous Thermoplastics at Large Strains Based on Molecular Dynamics Simulations

Dynamic In-Plane Shear Mechanical Behavior of Carbon Fiber/Epoxy Composite at Different Temperatures

Tensile Behavior of Acrylonitrile Butadiene Styrene at Different Temperatures

Experimental study on impact tensile properties of polycarbonate at low temperature

Study on mechanical and thermal properties of a modified epoxy resin

Experimental Investigation and Modeling of the Mechanical Properties of Construction PMMA at Different Temperatures

Study of self-heating and local strain rate in polyamide-6 and short fibre glass/polyamide-6 under tension through synchronised full-field strain and temperature measurements

Analysis of Tensile Failure Behavior of Metal Fiber Laminates Under Different Temperature Environments

Experimental Study on the Dynamic Tensile Behavior of A Poly-Crystal Pure Titanium at Elevated Temperatures

Dynamic mechanical properties and constitutive model of photosensitive resin specimens at different temperatures

Experimental and numerical research of temperature on tensile properties of multiaxial warp‐knitted composites

Tensile mechanical behavior and failure mechanisms of fiber metal laminates under various temperature environments

Effects of temperature and low strain rate on tensile performance of aramid fiber bundle

Effect of Tension Temperature on the Anisotropy of Tensile Behavior for Az31 Alloys: A Visco-Plastic Self-Consistent Analysis

Development of dynamic constitutive model of epoxy resin considering temperature and strain rate effects using experimental methods

Experimental Study on Tensile Properties of CP-Ti Athigh Strain Rate and Different Temperatures