Abstract:The original Johnson-Cook model's poor prediction of W90 alloy stress at high strain rate and high and low temperatures restricts research and utilization of this alloy. This study used a Split Hopkinson Pressure Bar (SHPB) device to conduct dynamic compression tests on W90 alloy over a temperature range of [-90°C,700°C] and analyze its mechanical behavior. We examined the material's different plastic phase characteristics at high and low temperatures and conducted microstructure research on impact test specimens. Then, we analyzed the stress-strain data from SHPB experiments and quasi-static compression tests on the classical Johnson-Cook model. The original Johnson-Cook model was calibrated using the stress-strain data from SHPB and quasi-static compression tests, and the modified Johnson-Cook model was established and verified. The results show that: low temperature significantly strengthens the material's stress, while increasing temperature thermal softening reduces stress; increasing strain rate increases the strain generated by the workpiece, causing faster strain hardening and thermal softening effects, resulting in higher and more stable stress; low temperature makes thicker grain boundaries, increasing plastic stress, and increasing strain rate also increases plastic stress, as well as making the material's grain boundaries thicker. The increase of strain rate makes the grain more dense, which will also show up in the increase of stress on the macroscopic level; the modified Johnson-Cook model in this paper has high agreement with experimental data, with a mean value of MAPE of only 1.85 %,which is 90.20 % lower than the traditional model, and the average value of the RMSE is 85.56 % lower than the traditional model. The modified model significantly outperforms the traditional model in predicting stress and better describes stress changes in W90 at different temperatures.

Experimental Study on Tensile Properties of CP-Ti Athigh Strain Rate and Different Temperatures

Experimental Study of Tensile Property of Cp-Ti at Intermediate Strain Rates

Experimental Study on Tension Behavior of Pure Titanium at High Strain Rates

Experimental Study of Mechanical Properties of CFRP under Different Strain Rates and Temperatures

Experimental Study on the Dynamic Tensile Behavior of A Poly-Crystal Pure Titanium at Elevated Temperatures

Research on stress relaxation behavior of TA15 titanium alloy

Stress-Strain Curves and Modified Material Constitutive Model for Ti-6Al-4V over the Wide Ranges of Strain Rate and Temperature

Influences of temperature and strain rate on deformation twinning of polycrystalline titanium

Tensile Mechanical Behaviour of Ultra-High Strength Cold Rolled Dual Phase Steel DP1000 at High Strain Rates

The Constitutive Responses of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy at High Strain Rates and Elevated Temperatures

Dynamic Mechanical Properties and Modified Material Constitutive Model for Hot Forged Ti2AlNb over Wide Ranges of Temperature and Strain Rate

Dynamic Mechanical Behavior and Modified Johnson-Cook Model of Ti60 Alloy under High-temperature and High-strain-rate Conditions

Temperature-Dependent Tension Plastic Deformation and Fracture Behavior of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy at High Strain Rates

Experimental Study of 20# Steel under Tensile Impact

High Strain-Rate Tensile Experiment on Polycarbonate Bar

Strain Rate Sensitivity of Tensile Properties in Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy: Experiments and Constitutive Modeling

Thermomechanical Response of Commercially Pure Titanium under Large Plastic Deformation at High Strain Rates

Dynamic Strain-Rate Effect On Uniaxial Tension Deformation Of Ti5al2.5sn Alpha-Titanium Alloy At Various Temperatures

Strain-Rate-Dependent Tensile Response of Ti–5Al–2.5Sn Alloy

Mechanical properties and JC constitutive modification of tungsten alloys under high strain rates and high/low temperatures

Tensile Behavior of Ti-5Al-2.5Sn Alloy at Low Temperatures and High Strain Rates