Abstract:The high temperature tensile test of Ti-47.5Al-2.5 V-1.0Cr-0.2Zr alloy was carried out by electronic universal testing machine under the condition of 750–900 °C/10 −5 –10 −3 s −1 . The hot tensile stress-strain curves were analyzed, and the constitutive model under hot tensile conditions was established. The microstructure transformation rule and deformation mechanism during tensile process were determined. The results show that the hot tensile curve is longer in the steady-state flow stage corresponding to lower strain rate and higher tensile temperature, the true stress declines and the elongation at break increases. The constitutive equation was established based on the tensile curve data, and the corresponding thermal activation energy was 310.3 kJ/mol. As the rise of tensile temperature and the decline of strain rate, the proportion about cross-layer fracture in the tensile fracture morphology decreases, the number of dimples increases, more lamellar structures change into recrystallized structures, and the softening effect of the alloy is more obvious. The dislocation deformation mechanism mainly includes the existence of dislocation slip and climb, dislocation intersection and dislocation ring or dislocation network formation. Twinning deformation is also another important mechanism of high temperature tensile deformation of TiAl alloy. Twins are formed in parallel with each other, so that the deformation can be further carried out. The dislocations and twins in the deformed microstructure will provide nucleation conditions for recrystallized grains. The dynamic recrystallization(DRX) grains are preferentially formed around the grain boundary and the vicinity of dislocation and twin is also preferred nucleation site for DRX. The DRX behavior is the main softening mechanism, and DRX size and volume fraction corresponding to lower tensile rate and higher tensile temperature are larger.

Influences of temperature and strain rate on deformation twinning of polycrystalline titanium

Modeling the Strain Rate-Dependent Constitutive Behavior in Nanotwinned Polycrystalline Metals

Experimental Study for the Influence of Twinning on the Plastic Deformation of Pure Polycrystalline Titanium

Influence of strain rates on deformation mechanism of duplex TiAl intermetallics

Mechanical Behavior and Deformation Modes of Commercially Pure Titanium under Impact Tensile Load

Effect of Strain Rate and Temperature on the Deformation Behavior in a Ti-23.1Nb-2.0Zr-1.0O Titanium Alloy

Dynamic Strain-Rate Effect On Uniaxial Tension Deformation Of Ti5al2.5sn Alpha-Titanium Alloy At Various Temperatures

The Microstructures and Deformation Mechanism of Hetero-Structured Pure Ti under High Strain Rates

Microscopic Mechanisms Underlying the Dynamic Tensile Behaviors of a Commercially Pure Titanium at Elevated Temperatures

Strain rate effect on the tensile behavior of Duplex Ti–46.5Al–2Nb–2Cr intermetallics at elevated temperatures

Temperature and Strain Rate Effect of the Deformation-Induced Phase Transformation in Pure Titanium Nanopillars Oriented along [0 0 0 1]

Constitutive Model and Microstructure Evolution of a Novel TG6 High-Temperature Titanium Alloy during Hot Deformation

Experimental Study on the Dynamic Tensile Behavior of A Poly-Crystal Pure Titanium at Elevated Temperatures

Influence of twinning behavior on plasticity of TA18 titanium alloy tubes

Experimental Study of Tensile Property of Cp-Ti at Intermediate Strain Rates

Tensile Impact Behavior and Deformation Mechanism of Duplex TiAl Intermetallics at Elevated Temperatures

In situ EBSD study of the twinning deformation behaviors in pure titanium

Microstructure evolvement of isometry TiAl under tensile impact loadings

Twinning Behavior and Its Effect on Mechanical Behavior of Commercial Titanium at Cryogenic Temperature

Twinning induced plasticity in commercially pure titanium at low temperature

Study on high temperature tensile constitutive behavior and deformation mechanism of Ti-47.5Al-2.5 V-1.0Cr-0.2Zr alloy