Abstract:This study investigates the relationship between aging temperature on the precipitation behavior and mechanical properties of a gravity cast Al-5.0Mg-3.0Zn-1.0Cu (wt%) alloy. After solution treatment at 470 °C for 24 h, alloys were aged at 120, 150 and 175 °C. Upon analyzing the samples, the alloys displayed different age hardening behaviors due to the variations in aging temperature. An increase in aging temperature not only reduced the peak aging time significantly, but also changed the distribution of precipitates. Numerous GPII zones and T′ precipitates (precursors of T-Mg32(AlZn)49) were homogeneously distributed within matrix at a higher aging temperature and the volume fraction of T′ precipitates increased. Tensile test results for peak-aged samples determined that both yield strength (YS) and ultimate tensile strength (UTS) increased, while elongation (EL) decreased with increasing temperature. The increase in the YS can be attributed to the higher volume fraction of T′ precipitates caused by the higher aging temperature. Moreover, the impact toughness decreased (due to a continuous decrease in EL) as the aging temperature increased. By adjusting aging temperature from 120 to 175 °C, YS increased from 377 to 451 MPa, while EL decreased from 13.8% to 5.2%. After peak aging treatment at 150 °C, the alloy appears to possess optimal mechanical properties with YS, UTS, EL and toughness being 441 MPa, 496 MPa, 9.6%, and 8.1 J/cm2, respectively. These finding suggest that there are many potential advantageous applications for this alloy within automobile components requiring high strength and toughness.

Aging precipitation behavior and properties of Al–Zn–Mg–Cu–Zr–Er alloy at different quenching rates

Atomic-scale study on the precipitation behavior of an Al-Zn-Mg-Cu alloy during isochronal aging

The effect of quenching rates on microstructure and mechanical properties of an Al-Si-Cu-Mg alloy

Effect of quenching rate on strengthening behavior of an Al-Zn-Mg-Cu alloy during natural ageing

Effect of Quenching Rate on Microstructure, Mechanical and Corrosion Properties of Al-Zn-Mg-Cu-Cr-Zr Alloy

Residual stress and precipitation of Mg-5Zn-3.5Sn-1Mn-0.5Ca-0.5Cu alloy with different quenching rates

Precipitate Behavior, Mechanical Properties and Corrosion Behavior of an Al-Zn-Mg-Cu Alloy during Non-Isothermal Creep Aging with Axial Tension Stress

Quench rate sensitivity of age-hardenable Al-Zn-Mg-Cu alloys with respect to the Zn/Mg ratio: An in situ SAXS and HEXRD study

Microstructure evolution and quench sensitivity characterizations of Mg-9.5Gd-0.9Zn-0.5Zr alloy

Precipitated phase characteristics and fracture behaviour of cast Al–Cu–Mn alloy

Aging precipitation characteristics and tensile properties of Al–Zn–Mg–Cu alloys with different additional Zn contents

Quantified effect of quench rate on the microstructures and mechanical properties of an Al–Mg–Si alloy

Effect of Over-Aging Degree on Microstructures, Precipitation Kinetics, and Mechanical Properties of an Ultra-High-Strength Al-Zn-Mg-Cu Alloy

Precipitation behavior of an Al–Cu–Li–X alloy and competing relationships among precipitates at different aging temperatures

Effects of aging treatment on the precipitation behaviors and mechanical properties of Al-5.0Mg-3.0Zn-1.0Cu cast alloys

Study on quenching sensitivity of an Al–Zn–Mg–Cu alloy containing trace amounts of Sc and Zr

Microstructure, mechanical properties and residual stress of high vacuum die casting AlSi10MgMn alloys with different spray quenching

Aging behavior of an Al–Cu–Mg alloy

Effect of aging route on the precipitation behavior and thermal stability of Al-Cu-Mg-Ag alloy

Effect of aging time on discontinuous precipitates, continuous precipitates and mechanical properties of AZ80A magnesium alloy

Influence of Zn Addition on the Aging Precipitate Behavior and Mechanical Properties of Al-Cu-Li Alloy