Abstract:Strain-induced precipitation was systematically investigated in austenitic Inconel 617B superalloy (IN617B) after deformation of 0.2 true strain in its service temperature range (700–850 °C). The precipitation-time-temperature (PTT) curves obtained by stress relaxation experiments showed a classic C-shape with the nose temperature of 800 °C, and a minimum incubation period of 30 s, and the main strain-induced precipitate was M23C6 carbide. After specimens deformed at 800 °C to a strain of 0.2 were held between 10 and 1000 s, they underwent a second-pass strain test, during which the M23C6 precipitates evolved and influenced the flow stress; this behavior was investigated. During the nucleation, growth, and coarsening of the strain-induced precipitates, the morphology of the M23C6 particles gradually changed from spherical to polygonal with increasing size, but the precipitates always maintained their cube-on-cube orientational relationship with the austenitic matrix. During the nucleation stage before 30 s, many pre-precipitation clusters and weak static recovery softening led to low second-deformation flow stress, which persisted at approximately 630 MPa. In the precipitation growth phase before 360 s, recovery softening balanced precipitation hardening. The strain-induced precipitates grew larger, and they were able to pin dislocations. In addition, some complex microstructures resulting from particle collisions were observed. This resulted in the maximum rate of increase of the second deformation flow stress, which quickly reached almost 700 MPa. When the holding time was extended to 1000 s, the recovery softening effect further increased, while the M23C6 particles gradually coarsened; this weakened the increasing trend of the second deformation flow stress, which increased to only 715 MPa at 1000 s

Effect of orientation on the tensile and creep properties of coarse-grained INCONEL alloy MA754

An Investigation of the Effect of High-Temperature Cyclic Straining and Creep Loading on Tensile Mechanical Properties of GH4145/SQ Alloy

In-situ Study of the Effect of Grain Boundary Misorientation on Plastic Deformation of Inconel 718 at High Temperature

Creep Anisotropy Behavior, Deformation Mechanism, and Its Efficient Suppression Method in Inconel 625 Superalloy

Creep Performance Study of Inconel 740H Weldment Based on Microstructural Deformation Mechanisms

Creep Behavior and Microstructure Evolution of Ni-based Alloy IN617 at 1000 °C

Effects of homogenization temperature on creep performance of laser powder bed fusion-fabricated Inconel 718 at 650 °C

Mechanisms of deformation, damage and life behavior of inconel 617 alloy during creep-fatigue interaction at 700 °C

Microstructure Evolution and Mechanical Properties of Inconel 740H During Aging at 750 °C

Temperature dependence of deformation behavior, microstructure evolution and fracture mechanism of Inconel 625 superalloy

Investigation of short-term creep properties of a coarse-grained Inconel 718 fabricated by directed energy deposition compared to traditional Inconel 718

Coarsening Behavior of Grain Boundary M23C6 in Inconel 740H During Creep

Change of Grain Orientation and Effect of Grain Size on It in Creep Deformed Hastelloy X

Microstructure and Damage Evolution of Inconel 740H Welded Joint during Creep Process at 750 °C

In-situ SEM study of temperature-dependent tensile behavior of Inconel 718 superalloy

Experimental characterization of flat indentation creep behaviour of Inconel 617

Creep beh avior of Inconel 600 alloy used for nuclear power

Detrimental Effect of Cellular Precipitation on the Creep Strength of Inconel740h

The Experimental and Numerical Studies on Multiaxial Creep Behavior of Inconel 783 at 700 °C

An Alternative Casting Technique to Improve the Creep Resistance of Cast INCONEL Alloy 740H

Evolution of strain-induced precipitates in Inconel 617B alloy and their effect on flow behavior