Abstract:It is essential to study the tensile fracture mechanism of additively manufactured materials and develop the effective process treatment techniques to improve their fracture resistance. In this paper, the effects of different treatment processes on the microstructure and tensile fracture properties of TC17 titanium alloy melted by laser selective zone melting were investigated. The static tensile fracture morphological characteristics were observed by combining SEM and EDS. The metallographic microstructure after chemical corrosion was observed optically. And the tensile fracture morphology of the three states of TC17 titanium alloy samples at room temperature conditions was investigated. The results show that the metallographic matrix microstructure of TC17 titanium alloy after HT, HIP and HIP-HT treatments was a bimodal structure with α+β phases, i.e., β phase was in the form of a net basket, and α phase was in the form of a coarse bar. The grain sizes of the samples treated by different processes were different, but the difference in grain size of the HT-treated tissues was small, and the difference in grain size of the HIP-HT-treated tissues was large. And the coarse α-phase segregation could be seen at the edge of the samples. The 3D-printed materials had complex changes in anisotropic properties affected by the printing structure and tissue. The printed tissues were brittle and had high internal stresses. These problems were partly improved at high temperatures, but they still existed. The HIP-HT-treated materials had a large α+β-phase bimodal structure. The HT-treated material had coarse grains and precipitation phases, poor room temperature plasticity, and improved high temperature plasticity. After HT treatment, the original printing microstructure changed, the strength and plasticity were significantly improved, but the macroscopic printing structure still had a slight influence on the fracture morphology. When HIP treatment temperature was higher, the influence of macroscopic printing structure basically disappeared, but the grain and microstructure grew up, and the strength and plasticity were slightly lower than that of the HT treatment. HIP process basically eliminated the unfused defects of the three-dimensional morphology, and the local weak bonding zone formed.

Effects of Multiple Laser Repairs on Microstructure and Hardness of ZTC4 Titanium Alloy

Superior High-Cycle Fatigue Property Through In-Situ Precipitation of Α' Martensite in Additively Repaired Titanium Alloy

Microstructures and mechanical properties of Ti6Al4V alloy repaired by the technology of point-mode forging and laser repairing

Microstructural Characterization of Pure Titanium Treated by Laser Surface Treatment under Different Processing Parameters

In-situ investigation on tensile deformation and fracture behaviors of inhomogeneous microstructure during laser repair of Ti-6Al-4 V titanium alloy

Microstructure and Mechanical Properties of Arc Zone and Laser Zone of TC4 Titanium Alloy Laser–TIG Hybrid Welded Joint

Microstructure and tensile properties of transient liquid phase (TLP) sintering repaired Ti-6Al-4V alloys with large area hole defect

Effect of Scanning Strategy on Microstructure Evolution and Stress Control in Laser Cladding Repair of Ti6Al4V Alloy

Effect of Laser Heat Input on Microstructure and Fatigue Behavior of TC17 Titanium Alloy Laser Welded Joint

Effect of three-stage heat treatment on the composite waveform and variable amplitude fatigue properties of TC4 titanium alloy pulsed laser-arc hybrid welded joints

Influence Of Processing Parameters On The Microstructure Of Tc4 Titanium Alloy By Laser Micro Cladding Deposition Manufacturing

Effects of different treatment processes on microstructure and tensile fracture behaviour of selected laser melting TC17 titanium alloy

Investigations into the Improvement of the Mechanical Properties of Ti-5Al-4Mo-4Cr-2Sn-2Zr Titanium Alloy by Using Low Energy Laser Peening Without Coating.

Effects of Laser Shock Peening on Microstructure and Mechanical Properties of TC17 Titanium Alloy

Microstructure and wear resistance of laser clad composite coating on TC4 titanium alloy surface

Effects of Pulsed Current on the Microstructure and Properties of Laser Cladded TC17 Titanium Alloy

High Cycle Fatigue Performance in Laser Shock Peened TC4 Titanium Alloys Subjected to Foreign Object Damage

Effect of Diameter and Content of Zirconium Dioxide on the Microstructure and Mechanical Properties of the TC17 Titanium Alloy Repaired by Wire Arc Additive Manufacture

Microstructure and anti-ablation of laser cladding Ti-Zr-B-C coating on TC11 titanium alloy

Effect of Zr on microstructure and properties of TC4 alloy fabricated by laser additive manufacturing

Effect of laser power on microstructure and properties of Ti-Al/WC composite coatings