Abstract:Aimed at the problem of insufficient heat resistance and poor ablation resistance of phenolic resin (RF), and the compatibility of SiO2 particles with phenolic resin, the nano-scale SiO2/RF hybrid aerogel was prepared by the co-gel method. The interpenetrated gel network was constructed to increase the compatibility of two phases. The microstructure, chemical structure and thermophysical properties of the SiO2/RF hybrid aerogel were explored. The silica-modified phenolic/carbon fiber composite material was prepared. The ablation properties of the composite material before and after modification were compared. The results show that the hybrid aerogel possesses a bi-continuous structure of skeleton and pores. The density of the hybrid aerogel fluctuates in the range of 0.145-0.160 g/cm(3). As the silica content increases, the residual carbon ratio of the hybrid aerogel increases, and the Si-O bond absorption vibration peak is more obvious, but XRD has no diffraction peak. Considering the pore size distribution and thermal physical properties, the silica-modified phenolic/carbon fiber composite material was prepared with the best performance hybrid aerogel. The mass ablation rate of the modified composite material is 0.046 g/s, and the linear ablation rate is 0.074 mm/s. Compared with the unmodified composite material, the mass ablation rate is reduced by 20.7%, the linear ablation rate is reduced by 21.3%. The oxidation resistance and the residual carbon ratio of the modified material are significantly improved.

Improved interfacial strength and ablation resistance of carbon fabric reinforced phenolic composites modified with functionalized ZrSiO4 sol

Ablation Behavior of a Carbon Fabric Reinforced Phenolic Composite Modified by Surface-Decorated ZrB2/SiC

Ablation Behavior of a Carbon Fabric Reinforced Phenolic Composite Modified by Surface-Decorated ZrB<sub>2</sub>/SiC

Ablation Behavior and Mechanism of TaSi2-modified Carbon Fabric-Reinforced Phenolic Composite

Improved Thermal Stabilities, Ablation and Mechanical Properties for Carbon Fibers/Phenolic Resins Laminated Composites Modified by Silicon-containing Polyborazine

Synthesis and Anti-ablation Properties of in Situ ZrC Modified Carbon/Carbon Composites

Oxidation and ablation behaviours of ZrC modified carbon/carbon composites

Improvement of Carbon Fiber/phenolic Composite Properties by Low-Loading Graphene Oxide and SiO2 Nanoparticles

Preparation and ablation properties of ZrB 2 –SiC protective laminae for carbon/carbon composites

Mechanical Property, Oxidation and Ablation Resistance of C/C–ZrB2–ZrC–SiC Composite Fabricated by Polymer Infiltration and Pyrolysis with Preform of Cf/ZrB2

Enhanced Anti-Ablation Performance of Carbon/carbon Composites Modified with ZrC-SiC

Enhanced Mechanical Property, High-Temperature Oxidation and Ablation Resistance of Carbon Fiber/phenolic Composites Reinforced by Attapulgite

Preparation and Ablation Performance of Silica Modified Phenolic/carbon Fiber Composite

Enhanced ablative resistance of C/C composites with densified ZrB 2 -based ceramics by incorporation of Mo as interface layer

Enhanced mechanical, thermal and ablation properties of carbon fiber/BPR composites modified by mica synergistic MoSi2 at 1500 °C

Ablation Behaviour and Mechanical Performance of ZrB2-ZrC-SiC Modified Carbon/carbon Composites Prepared by Vacuum Infiltration Combined with Reactive Melt Infiltration

Oxidation and ablation behaviors of carbon fiber/phenolic resin composites modified with borosilicate glass and polycarbosilane interface

The effects of ZrSi 2 on the ablation and insulation performances of low-density carbon-phenolic composites

Ablation behaviour of Csf/ZrB2-SiC composites fabricated by direct ink writing and reactive melt infiltration

Improved Ablation Resistance of Carbon–phenolic Composites by Introducing Zirconium Diboride Particles

3D needle-punched carbon/quartz fabric reinforced nanoporous phenolic composites with co-optimized mechanics, insulation and ablation