Abstract:Objective To explore the applied value of computer-aided design and three-dimensional printing technology in osteotomy for chin width and prominent mandibular angle.Methods Sixteen patients with chin width and prominent mandibular angle were admitted to the Plastic Surgery Ward of the Second Affiliated Hospital of Zhengzhou University.All patients underwent preoperative computer-aided design,three-dimensional reconstruction of head and face,reconstruction of mandibular nerve canal,intelligent osteotomy line design of chin and mandible,simulation of chin and mandibular angle osteotomy,3-D printing of surgical template to complete osteotomy,and internal fixation of chin osteotomy plate.The mandibular angle (Co-Go-Me),mandibular ramus height (Co-Go),mandibular body length (Go-Me),subfacial width (Go-Go'),chin nodule width (Ge-Ge') and face height (N-Me) were measured preoperation,before surgical simulation and postoperation.Co-Go-Me,Co-Go/Go-Me,Go-Go'/N-Me and Ge-Ge'/N-Me were compared and analyzed in preoperation,before surgical simulation and postoperation.Results All the patients were satisfied with their facial shape.The mandible was almost symmetrical after operation.No complications such as nerve injury and infection occurred after operation,which fully met the preoperative design requirements.The mandibular angles in the left and right sides of patients before operation were significantly less than those after operation (t =2.890,2.886,P ＜ 0.05).There was no significant difference in the mandibular angles in the left and right sides of pa tients before and after operation (t =0.200,0.201,P ＞ 0.05).The average mandibular angles after operation were (123.9 ± 3.0)°.Co-Go/Go-Me in the left and right sides of patients before operation was significantly higher than that after operation (t =3.607,2.860,P ＜ 0.05).There was no significant difference in the simulated Co-Go/Go-Me in the left and right sides before and after operation (t =0.067,0.069,P ＞ 0.05).The ratio of the length of the left and right mandibular body to the height of the ascending ramus was close to 2:1.Preoperative Go-Go'/N-Me was significantly higher than that post-operation (t =3.102,P ＜0.05).Preoperative simulated Go-Go'/N-Me was not significantly different from postoperative Go-Go'/N-Me (t =2.011,P ＞0.05).Preoperative Ge-Ge'/N-Me was significantly higher than that post-operation (t =3.010,P ＜ 0.05).Preoperative simulated Ge-Ge'/N-Me was not significantly different from post-operative Ge-Ge'/N-Me (t =2.010,P ＞ 0.05).Conclusion The application of computer-aided design and three-dimensional printing technology in osteotomy for large chin and hypertrophic mandibular angle can significantly improve the accuracy of operation,reduce the difficulty of operation,improve the cosmetic effect,and reduce the occurrence of complications such as infection and injury of important nerves and blood vessels.

Simultaneous Orthognathic Surgery and Mandibular Contour Osteoplasty for Treating Mandibular Protrusion with High Gonial Angle.

Simultaneous correction of bilateral temporomandibular joint ankylosis with mandibular micrognathia using internal distraction osteogenesis and 3-dimensional craniomaxillofacial models.

Combined Use of Facial Osteoplasty and Orthognathic Surgery for Treatment of Dentofacial Deformities

Correction of Facial Asymmetry Associated with Vertical Maxillary Excess and Mandibular Prognathism by Combined Orthognathic Surgery and Guiding Templates and Splints Fabricated by Rapid Prototyping Technique

Treatment of Dentofacial Deformities Secondary to Osteochondroma of the Mandibular Condyle Using Virtual Surgical Planning and 3-Dimensional Printed Surgical Templates.

The Application of 3D Printing Technology for Simultaneous Orthognathic Surgery and Mandibular Contour Osteoplasty in the Treatment of Craniofacial Deformities

Standardized Protocol for Virtual Surgical Plan and 3-Dimensional Surgical Template-Assisted Single-Stage Mandible Contour Surgery

Combined use of rapid-prototyping model and surgical guide in correction of mandibular asymmetry malformation patients with normal occlusal relationship.

One-Stage Treatment for Maxillofacial Asymmetry with Orthognathic and Contouring Surgery Using Virtual Surgical Planning and 3D-Printed Surgical Templates.

[Combined Surgical-Orthodontic Correction for Mandibular Protrusion].

Application of guiding templates and splints fabricated by rapid prototyping technique in correction of facial asymmetry

Application of Segmented Template in Three-Dimensionally Guided Mandibular Angle Osteotomy

Treatment of Complex Dentofacial Deformities Secondary to Osteochondroma of the Mandibular Condyle with 3D Printed Surgical Templates

Evaluation of Mandibular Symmetry in Patients with Condylar Osteochondroma Who Underwent Intro-Oral Condylar Resection and Simultaneous Bimaxillary Orthognathic Surgery.

Computer-assisted mandibular curved osteotomy: An automatic method to design the new aesthetic gonion and osteotomy line

Endoscope-assisted Conservative Condylectomy Combined with Orthognathic Surgery in the Treatment of Mandibular Condylar Osteochondroma.

Correcting Facial Asymmetry Through Guided Plate Assisted Mandibular Angle Osteotomy

[Combined surgical and orthodontic treatment of severe maxillary anterior teeth and dentoalveolar bone protrusion].

Surgical Precision Analysis of Orthognathic Surgery Combined With Invisible Orthodontic

[Application of three-dimensional printing technique in correction of mandibular prognathism]

Application of Three-Dimensional Printing Technology in Osteotomy for Chin Width and Prominent Mandibular Angle