Selenium concentrations in maternal and umbilical cord blood at 24-42 weeks of gestation: basis for optimization of selenium supplementation to premature infants.

I. Makhoul,R. Sammour,E. Diamond,I. Shohat,A. Tamir,R. Shamir

DOI: https://doi.org/10.1016/J.CLNU.2003.08.004

IF: 7.643

2003-08-01

Clinical Nutrition

Abstract:

What problem does this paper attempt to address?

[Application of Computer Aided Design-Computer Aided Manufacture Technique in Mandible Defect Reconstruction with Individual Titanium Prosthesis].

Xin Xu,Jun-lie Yan,Fei-yun Ping,Jun Chen,Feng-guo Yan,Yi-dan Shan

DOI: https://doi.org/10.3760/cma.j.issn.1002-0098.2011.07.009

2011-01-01

Abstract:OBJECTIVE:To investigate the application of computer aided design-computer aided manufacture (CAD-CAM) technique in the reconstruction of mandible defect with individual titanium prosthesis.METHODS:Six patients with large mandibular ramus and angle tumor were spiral CT scanned preoperatively, and the CAD-CAM was used to design and make individual titanium prosthesis for reconstructing the mandibular defects after resection of the tumor. The prosthesis were assembled during operation. Postoperative follow-up period was 9 - 38 months.RESULTS:The design and manufacture of titanium prosthesis by use of CAD-CAM technique was convenient and the prosthesis fitted the defects very well. The outline of the face, the occlusion and function were restored. After 9 - 38 months of follow-up, the mandibular symmetry was good.CONCLUSIONS:The application of CAD-CAM provided accurate simulation and fast manufacturing process for the titanium prosthesis in the repair of mandibular defect.
[Application of Computer Aided Design/computer Aided Manufactured Techniques in Mandible Defect Reconstruction].

Xin Xu,Fei-yun Ping,Jun Chen,Jun-lie Yan,Feng-guo Yan

DOI: https://doi.org/10.3760/j.issn:1002-0098.2007.08.013

2007-01-01

Abstract:OBJECTIVE:To investigate the application of CAD/CAM technique in reconstruction of mandible defect.METHODS:Before surgery, three-dimensional computed tomography was performed in 23 patients with mandible lesions, then the CT data were transformed into a readable format to produce facsimile models by using rapid prototyping (RP) techniques. When individual mandibular models were produced, evaluation and surgical simulation were performed on the model, which included measuring range of mandible lesions, prefabrication of mandibular reconstructive titanium plates or distractors, ascertaining precise position of transport disk, and shaping the free vascularized fibula, etc. According to the simulation, the mandible reconstruction was accomplished in operation.RESULTS:The surgical simulation on the model produced by CAD/CAM technique highly resembled the real operation. The measurements of the lesion on the model were completely correspondent with those found in operation, and the prefabricated plates and distractor fitted the contour of the mandible. The operation time shortened and the results were satisfactory. The post-operation X-ray showed that the mandible was symmetrical and the maxillofacial contour maintained.CONCLUSIONS:CAD/CAM technique was very helpful for simulation of anatomically complicated mandible defect. By preoperative simulation of the mandible and lesions, surgeons are able to improve or refine surgical planning so that better results can be assured.
Simultaneous correction of bilateral temporomandibular joint ankylosis with mandibular micrognathia using internal distraction osteogenesis and 3-dimensional craniomaxillofacial models.

Ping Feiyun,Liu Wei,Chen Jun,Xu Xin,Shi Zhuojin,Yan Fengguo

DOI: https://doi.org/10.1016/j.joms.2009.07.022

IF: 1.9

2010-01-01

Journal of Oral and Maxillofacial Surgery

Abstract:The present study evaluated the simultaneous correction of bilateral temporomandibular joint ankylosis with mandibular micrognathia using internal distraction osteogenesis (DO) with the help of a 3-dimensional craniomaxillofacial model technique.A total of 16 patients (age 18 to 43 years) with bilateral temporomandibular joint ankylosis and mandibular micrognathia were included in the present study. Obstructive sleep apnea and hypopnea syndrome was diagnosed in all patients preoperatively. Three-dimensional craniomaxillofacial models of the 16 patients were constructed using computed tomography and a rapid prototype technique. Simulation surgery and individual internal DO was performed on the models. The treatment included simultaneous DO of the mandibular body and transport DO for temporomandibular joint arthroplasty. The distraction was started on the seventh day after surgery. The distraction rate was 0.8 mm/day. The patients began active mouth opening postoperatively. Distracters were kept in place for 4 months after distraction completion and then removed. Polysomnography, cephalometry, and computed tomography were performed at 6 months postoperatively.The obstructive sleep apnea and hypopnea syndrome was cured, and the micrognathia was corrected in all patients. The average mouth opening increased from 4.6 mm preoperatively to 33.5 mm postoperatively. The average range of the sella-nasion-supramental angle increased from 68.7 degrees preoperatively to 77.6 degrees postoperatively. Bone formation in the distraction gaps was observed. The follow-up period was 29.7 months (range 6 to 52). No complications or recurrence of temporomandibular joint ankylosis or micrognathia occurred in any patient during the follow-up period.Bilateral temporomandibular joint ankylosis accompanied by mandibular micrognathia and obstructive sleep apnea and hypopnea syndrome can be corrected effectively by simultaneous internal DO. The application of preoperative simulation surgery using 3-dimensional craniomaxillofacial model has many advantages for planning the surgical method and precise operation. Our preliminary results have shown that it is a safe, effective, and feasible technique.
Application of CAD/CAM Techniques in Mandible Large-Scale Defect and Reconstruction with Vascularized Fibular Bone Graft

Xin Xu,Fei-yun Ping,Jun Chen,Feng-guo Yan,Hua-qing Mao,Yu-hua Shi,Zheng-yan Zhao

DOI: https://doi.org/10.3785/j.issn.1008-9292.2007.05.016

2007-01-01

Abstract:OBJECTIVE:To exploit computer-aided design and computer-aided manufactured (CAD/CAM) techniques and application in the reconstruction of mandible large-scale defect with vascularized fibular bone graft.METHODS:Before actually performing surgery, three-dimensional(3D) computed tomography(CT) was performed in 7 patients with mandibular large-scale defects, and 3D CT images were acquired by processing CT data. Then the CT data were transformed into a readable format and transferred to produce facsimile models by means of using rapid prototyping(RP) techniques. When individual mandibular models and enantiomorphous models were produced, evaluation and surgical simulation was performed in model, which included measuring range of mandible lesions, prefabrication of mandibular reconstructive titanium palate, precise position of titanium screws, shaping the free vascularized fibula by mandibular, etc. According to the simulations, the mandible reconstructions were finished in operation.RESULT:CAD/CAM techniques and application can distinctly display the mandibular lesions and ambient relationships, which is very useful for clinical assessment and surgical planning. Particular advantages were the unlimited trials with the imaging method, and the feeling of reality with the model method. The actual operative time was shortened, and surgery results were satisfactory with few complications.CONCLUSION:CAD/CAM techniques are very helpful for simulation of mandible large-scale defect with complicated anatomical and reconstructive problems. By preoperative simulation of procedures, surgeons can improve or refine treatment planning using this method and improve postoperative results.
[Application of Three-Dimensional Printing Technique in Repair and Reconstruction of Maxillofacial Bone Defect].

Dan Yu,Jianhua Liu,Huiyong Zhu,Zhiyong Li,Xu Huang,Dong Wei,Yi Lin,Jianfeng He,Wenquan Zhao

DOI: https://doi.org/10.7507/1002-1892.20140066

2014-01-01

Abstract:OBJECTIVE:To explore the application of three-dimensional (3-D) printing technique in repair and reconstruction of maxillofacial bone defect.METHODS:The related literature on the recent advance in the application of 3-D printing technique for repair and reconstructing maxillofacial bone defect was reviewed and summarized in the following aspects: 3-D models for teaching, preoperative planning, and practicing; surgical templates for accurate positioning during operation; individual implantable prosthetics for repair and reconstructing the maxillofacial bone defect.RESULTS:3-D printing technique is profoundly affecting the treatment level in repair and reconstruction of maxillofacial bone defect.CONCLUSION:3-D printing technique will promote the development of the repair and reconstructing maxillofacial bone defect toward more accurate, personalized, and safer surgery.
THE APPLICATION OF RAPID PROTOTYPING IN THE ORTHOGNATHIC SURGERY

Fu-dong ZHU,Shi-fang ZHAO,Zhi-jian XIE,Zhe-feng YU,Chen JIANG

DOI: https://doi.org/10.3321/j.issn:0529-1356.2006.05.017

2006-01-01

Abstract:Objective: To construct a geometric skull model by using three-dimensional reconstruction, computer tomography scanning and rapid prototyping technology and evaluate its significance in treatment of complex oral and maxillofacial deformities. Methods: A cranial and a goldenhar syndrome patient with complex oral and maxillofacial deformities bone received continuous volumetric scanning of skull and the data acquisition was done by an electron computed tomography, by which reconstruction was performed and the obtained images saved as STL files. Then the data were input into rapid prototyping machine to make three-dimensional geometric model. Direct measurement, designation and surgery simulation could be done on this three-dimensional model. Then the mandibular mirror physical model was manufactured using rapid prototyping according to the normal side. Results: A computer-aided model according to CT data could represent the three-dimensional anatomic structures and their relationships precisely. The replica exhibited dimensional errors ranging 0.02 mm to 0.53 mm. Which provided strong basis for accurate understanding of disease status and reasonable surgical plans and helped improve the curative effect of surgery. Conclusion: Rapid prototyping can help surgeons in many ways for therapy of the complex oral and maxillofacial deformities.
The use of modified 3D-printed reconstruction plates in mandible segmental defect rehabilitation: a case report

Yi-Wei Zhong,Zuo-Sen Wang,Wen-Jie Wu,Jie Zhang

DOI: https://doi.org/10.2217/3dp-2021-0032

2022-04-21

Journal of 3D Printing in Medicine

Abstract:The preliminary safety and accuracy of a modified 3D-printed reconstruction plate (3DPRP) for mandible segmental defects were evaluated. Two patients with mandible segmental defects who underwent reconstruction using 3DPRPs were included in the study. No dead space, wound healing failures or fractures were observed. The mean deviations for the two patients were 0.59 and 0.57 mm and the condyle changes were 1.01 and 0.88 mm. The deviations in the distances between both sides of the mandibles (D1–6) ranged from 0.67 to 1.16 mm and from 0.43 to 0.61 mm for the two patients. The preliminary results show that the modified 3DPRPs are safe and accurate.
Outcome Evaluation of Three-Dimensionally Printed Patient-Specific Surgical Plates for Mandibular Reconstruction

Wen-Bo Zhang,Chao-Fei Wang,Yao Yu,Shuo Liu,Lei-Hao Hu,Hui Yuh Soh,Jie Zhang,Xin Peng

DOI: https://doi.org/10.1177/19433875241272441

2024-01-01

Craniomaxillofacial Trauma & Reconstruction

Abstract:Study Design Prospective and retrospective studies.Objective The aim of this study was to evaluate the clinical effects and accuracy of three-dimensionally (3D)-printed patient-specific surgical plates used for mandibular defect reconstruction.Methods This study included patients who underwent mandibular defect reconstruction with vascularized autogenous bone grafts between January 2012 and August 2021. They were divided into experimental (fixation with 3D-printed surgical plates) and control (fixation with conventional surgical plates) groups. Flap survival rate, postoperative complications and patient self-evaluated facial appearance were compared. Mandibular reconstruction accuracy evaluation included postoperative position deviation of the whole mandible, transplanted bone graft, lower mandibular border, mandibular condyle, and mandibular angle on the reconstructed side compared to baseline.Results This study included 20 patients (14 males, six females; age, 39.45 +/- 11.69 years), ten each in the experimental and control groups. The mean follow-up was 16 +/- 22.05 (range, 6-99) months. All procedures were successful, no plate-related complications (breakage, loosening, or exposure of the surgical plates) were reported, and all patients were satisfied. The groups were statistically similar in th e position deviation of the whole mandible, transplanted bone graft, mandibular condyle, and mandibular angle, but the position and morphology of the lower mandibular border on the reconstructed side in the experimental group were better than those in the control group (P = 0.016).Conclusions 3D-printed patient-specific surgical plates could be applied in mandibular reconstruction safely and effectively, simplifying the surgical procedure, shortening the preoperative preparation times, achieving satisfactory outcomes, and improving the clinical effects and accuracy of individualized mandibular reconstruction.
Application of 3D printed titanium mesh and digital guide plate in the repair of mandibular defects using double-layer folded fibula combined with simultaneous implantation

Shangbo Li,Lian Mi,Li Bai,Zijian Liu,Li Li,Yupeng Wu,Liqiang Chen,Na Bai,Jian Sun,Yanshan Liu

DOI: https://doi.org/10.3389/fbioe.2024.1350227

IF: 5.7

2024-02-22

Frontiers in Bioengineering and Biotechnology

Abstract:Fibula transplantation plays an irreplaceable role in restoring the function and morphology of the defected mandible. However, the complex load-bearing environment of the mandible makes it urgent to accurately reconstruct the mandible, ensure the position of the condyle after surgery, and restore the patient's occlusal function and contour. The intervention of digital design and three-dimensional (3D) printed titanium mesh provides a more efficient method and idea to solve this problem. Digital design guides the accurate positioning, osteotomy, and simultaneous implant placement during surgery, and 3D printed titanium mesh ensures stable condyle position after surgery, restoring good mandibular function. The double-layer folded fibula maintains the vertical height of the mandible and a good facial contour, and simultaneous implant placement can establish a good occlusal relationship. This study conducted a retrospective analysis of five patients with jaw defects who underwent digital fibula reconstruction over the past 3 years. It was found that the surgical protocol combining digital design, 3D printed intraoperative guides, 3D printed titanium mesh, free fibula flap, immediate implant, and occlusal reconstruction to repair jaw defects had more ideal facial appearance and biological function. It will provide a more reliable surgical protocol for clinical management of large mandibular defects.

multidisciplinary sciences
Application of a three dimensional digital model for mandibular plastic surgery

CHAI Gang,ZHANG Yan,GUO Yu

DOI: https://doi.org/10.3969/j.issn.1673-7040.2008.05.020

2008-01-01

Abstract:Objective To establish a three dimensional(3D) digital model for cosmetic reduction of the mandibular angles.Methods This study was based upon computerized tomographic scans of 20 patients(all women) who complained of "square face".A 3D digital model of the mandible was established based on CT data.Using 3D imaging software,virtual mandibular angle osteotomy was then performed.The position and oblique angles of the osteotomy lines thus designed were documented.In addition,the mandibular angle between the mandibular body and ramus,the extroversion angles of the mandibular angles,the length of ramus and the distance between the bilateral mandibular angles were measured before and after the virtual surgery operation.Results 3D digital models of the mandible and the inferior alveolar nerve canals were successfully reconstructed with CT scanning and DICOM management.The parameters of the virtual osteotomy line were also recorded.There were significant differences in the mandibular angles between the mandibular body and ramus,the valgu angles of mandibular angles,the length of ramus and the distance between bilateral mandibles before and after the virtual surgery(P<0.05).Conclusion The application of a mandibular 3D digital model in the treatment of prominent mandibular angle has a high clinical guidance value.At the same time,it lays a foundation for the realization of digital navigation surgery.
Technical Procedures for Template-Guided Surgery for Mandibular Reconstruction Based on Digital Design and Manufacturing

Yun-feng Liu,Liang-wei Xu,Hui-yong Zhu,Sean Shih-Yao Liu

DOI: https://doi.org/10.1186/1475-925x-13-63

2014-01-01

BioMedical Engineering OnLine

Abstract:Background The occurrence of mandibular defects caused by tumors has been continuously increasing in China in recent years. Conversely, results of the repair of mandibular defects affect the recovery of oral function and patient appearance, and the requirements for accuracy and high surgical quality must be more stringent. Digital techniques — including model reconstruction based on medical images, computer-aided design, and additive manufacturing — have been widely used in modern medicine to improve the accuracy and quality of diagnosis and surgery. However, some special software platforms and services from international companies are not always available for most of researchers and surgeons because they are expensive and time-consuming. Methods Here, a new technical solution for guided surgery for the repair of mandibular defects is proposed, based on general popular tools in medical image processing, 3D (3 dimension) model reconstruction, digital design, and fabrication via 3D printing. First, CT (computerized tomography) images are processed to reconstruct the 3D model of the mandible and fibular bone. The defect area is then replaced by healthy contralateral bone to create the repair model. With the repair model as reference, the graft shape and cutline are designed on fibular bone, as is the guide for cutting and shaping. The physical model, fabricated via 3D printing, including surgical guide, the original model, and the repair model, can be used to preform a titanium locking plate, as well as to design and verify the surgical plan and guide. In clinics, surgeons can operate with the help of the surgical guide and preformed plate to realize the predesigned surgical plan. Results With sufficient communication between engineers and surgeons, an optimal surgical plan can be designed via some common software platforms but needs to be translated to the clinic. Based on customized models and tools, including three surgical guides, preformed titanium plate for fixation, and physical models of the mandible, grafts for defect repair can be cut from fibular bone, shaped with high accuracy during surgery, and fixed with a well-fitting preformed locking plate, so that the predesigned plan can be performed in the clinic and the oral function and appearance of the patient are recovered. This method requires 20% less operating time compared with conventional surgery, and the advantages in cost and convenience are significant compared with those of existing commercial services in China. Conclusions This comparison between two groups of cases illustrates that, with the proposed method, the accuracy of mandibular defect repair surgery is increased significantly and is less time-consuming, and patients are satisfied with both the recovery of oral function and their appearance. Until now, more than 15 cases have been treated with the proposed methods, so their feasibility and validity have been verified.
Application of Three-Dimensional Printing Technology in Osteotomy for Chin Width and Prominent Mandibular Angle

Wang Zijian,Kong Qingsheng,Wang Lu

DOI: https://doi.org/10.3760/cma.j.issn.1001-9030.2019.08.045

2019-01-01

Abstract:Objective To explore the applied value of computer-aided design and three-dimensional printing technology in osteotomy for chin width and prominent mandibular angle.Methods Sixteen patients with chin width and prominent mandibular angle were admitted to the Plastic Surgery Ward of the Second Affiliated Hospital of Zhengzhou University.All patients underwent preoperative computer-aided design,three-dimensional reconstruction of head and face,reconstruction of mandibular nerve canal,intelligent osteotomy line design of chin and mandible,simulation of chin and mandibular angle osteotomy,3-D printing of surgical template to complete osteotomy,and internal fixation of chin osteotomy plate.The mandibular angle (Co-Go-Me),mandibular ramus height (Co-Go),mandibular body length (Go-Me),subfacial width (Go-Go'),chin nodule width (Ge-Ge') and face height (N-Me) were measured preoperation,before surgical simulation and postoperation.Co-Go-Me,Co-Go/Go-Me,Go-Go'/N-Me and Ge-Ge'/N-Me were compared and analyzed in preoperation,before surgical simulation and postoperation.Results All the patients were satisfied with their facial shape.The mandible was almost symmetrical after operation.No complications such as nerve injury and infection occurred after operation,which fully met the preoperative design requirements.The mandibular angles in the left and right sides of patients before operation were significantly less than those after operation (t =2.890,2.886,P ＜ 0.05).There was no significant difference in the mandibular angles in the left and right sides of pa tients before and after operation (t =0.200,0.201,P ＞ 0.05).The average mandibular angles after operation were (123.9 ± 3.0)°.Co-Go/Go-Me in the left and right sides of patients before operation was significantly higher than that after operation (t =3.607,2.860,P ＜ 0.05).There was no significant difference in the simulated Co-Go/Go-Me in the left and right sides before and after operation (t =0.067,0.069,P ＞ 0.05).The ratio of the length of the left and right mandibular body to the height of the ascending ramus was close to 2:1.Preoperative Go-Go'/N-Me was significantly higher than that post-operation (t =3.102,P ＜0.05).Preoperative simulated Go-Go'/N-Me was not significantly different from postoperative Go-Go'/N-Me (t =2.011,P ＞0.05).Preoperative Ge-Ge'/N-Me was significantly higher than that post-operation (t =3.010,P ＜ 0.05).Preoperative simulated Ge-Ge'/N-Me was not significantly different from post-operative Ge-Ge'/N-Me (t =2.010,P ＞ 0.05).Conclusion The application of computer-aided design and three-dimensional printing technology in osteotomy for large chin and hypertrophic mandibular angle can significantly improve the accuracy of operation,reduce the difficulty of operation,improve the cosmetic effect,and reduce the occurrence of complications such as infection and injury of important nerves and blood vessels.
[Clinical application of virtual surgery combined with guide plate in reduction and fixation of condylar neck fracture in 7 patients]

Kai Ying,Liang Wang,Yong-Wu Zhu,Qian-Qian Li,Bin Mao

Abstract:Purpose: To explore the value of virtual surgery and 3D printing model combined with guide plate in treatment of mandibular condylar neck fracture. Methods: Seven patients with mandibular condylar neck fracture were scanned by CT for original data. The data were exported in DICOM format. A three-dimensional model was reconstructed using software, the fracture was reduced by virtual surgery, and the 3D model was printed by a 3D printer. A prebent titanium plate was used to fabricate the guide plate, which was used for reduction and fixation of the fracture block during surgery. Results: All the postoperative incisions revealed no signs of infection, the wounds were hidden and beautiful. The implanted titanium plates were highly compatible with the reduced fracture segments. The patients were followed up for 6 months after surgery, the condylar fracture healed well and there was no obvious displacement. The patient developed no mandibular deviation with a stable occlusion, and no occlusal pain was reported. No obvious temporomandibular joint disorder was present. Conclusions: Virtual surgery and 3D printing model combined with guide plate can ensure an accurate reduction of condylar neck fracture and simplify the operation process, which can be used as an accurate, efficient and predictable auxiliary method.
Clinical Application of Computer-assisted Three-dimensional Reconstruction Combined with 3D Printing in Mandibular Defect Reconstruction

Yang LI,Ying LIU,Weiguo QU,Gang QIU,Zhenyu QU,Ji WANG,Muqing NIU,Ying YU,Xinjuan CHEN

DOI: https://doi.org/10.3969/j.issn.1672-7185.2019.01.029

2019-01-01

Abstract:Objective To explore the clinical effect of computer-assisted three-dimensional reconstruction combined with 3D printing technology in the treatment of mandibular defects.Methods From September 2015 to March 2017,a total of 64 patients with mandibular defect,who underwent repair and reconstruction in Department of oral and maxillofacial surgery in Dalian Stomatology Hospital,were randomly divided into observation group(computer-assisted surgery) and control group(traditional surgery) according to different treatment methods.The operative time,intraoperative blood loss,therapeutic effect and satisfaction between two groups were observed and compared.Results The operation time and bleeding volume in the observation group were significantly lower than those in the control group (P < 0.05).After treatment,the grade I recovery rate in the observation group was significantly higher than that in the control group,and the satisfaction degrees in appearance recovery,chewing and pronunciation function was significantly higher than that in the control group (P < 0.05).Conclusion Computer-assisted three-dimensional reconstruction combined with 3D printing technology can repair mandibular defect accurately.The clinical effect is good and the patients' satisfaction is high,which is worth popularizing.
[Application of 3D printing technology under three-dimensional reconstruction in mandibular reconstruction].

Chen-xing Wang,Huai-qi Li,Zai-Ou Zhu,He-Ming Wu,Jin-hai Ye

2021-06-01

Abstract:PURPOSE To explore the application value of 3D printing technology under three-dimensional reconstruction in mandibular reconstruction. METHODS Eighty-four patients with mandibular defect reconstruction were divided into two groups by different operation methods: 3D group(n=42) and control group(n=42). Patients in the control group underwent routine operation, while patients in the experimental(3D) group underwent three-dimensional reconstruction with 3D printing technology. The operation conditions, incidence of complications, recovery of facial features and occlusal relationship were recorded. SPSS 23.0 software package was used for statistical analysis of the data. RESULTS The operation time of 3D group was significantly shorter than that of the control group, and the amount of bleeding was significantly less than that of the control group(P<0.05). The recovery rate of facial appearance and occlusal relationship in 3D group was significantly higher than in the control group(95.24% vs 78.57%, P<0.05). Compared with the control group, the movement distance of mandibular points in 3D group was significantly smaller before and after operation(P<0.05). The satisfaction scores of chewing function and pronunciation recovery in the two groups were close(P>0.05), but compared with the control group, the satisfaction scores of appearance recovery in the 3D group were significantly higher(P<0.05). CONCLUSIONS 3D reconstruction under 3D printing technology can reduce intraoperative bleeding, shorten the operation duration, and achieve good shape recovery with high degree of satisfaction.

Engineering,Medicine
Clinical application and accuracy analysis of 3D printing guide plate based on polylactic acid in mandible reconstruction with fibula flap

Po Wu,Lin Hu,Hao Li,Lin Feng,Yu Liu,Shuo Zhang,Xue-Chao Li,Mei-Ling Zhang,Shu-Yong Yang,Rong-Jian Lu

DOI: https://doi.org/10.21037/atm-20-6781

IF: 3.616

2021-03-01

Annals of Translational Medicine

Abstract:BACKGROUND: Due to the special anatomy morphology and physiological function of the mandible, it has always become a challenge to accurately reconstruct the mandibular defect in maxillofacial surgery. Digital three dimensions (3D) printing surgical guide, as the effective method for individual and accurate surgery, is a hotspot of clinical research at present. In this study, 3D printing PLA surgical guide plate was applied to reconstruct the mandibular defect with fibula flap, its clinical effect and accuracy were evaluated, which aimed to improve the accurate reconstruction of mandibular defects.METHODS: After sterilization, the dimension deformation of the PLA standard specimen were measured. Eighteen patients diagnose with mandibular tumor were collected as observation objects. Then partial mandible resection and simultaneous mandible reconstruction with fibula graft were implemented according to the computer-aided design plan. The clinical effects of 3D printing PLA guide plates application were evaluated by facial contours, occlusal stability and chewing function. Through registering the postoperative computed images reconstruction with preoperative designed shape, the reconstruction accuracy was evaluated by detecting the maximum difference including the distance between lateral convex point of the condyles, the distance between medial convex point of the condyles and the horizontal contained angle between long axis of the condyles.RESULTS: After high temperature steam sterilization, the curvature of the PLA specimen with 100% filling rate and 4.8 mm thickness were the smallest and their dimension deformation had no statistical significance (P>0.05). The minimally deformed 3D printing PLA guide plate were smoothly placed in the right place during the operation. After surgery, the face was symmetrical, the occlusal relationship was restored well and no deviation of the mandibular movement were found. The spiral computed tomography (SCT) scanning showed that the distance between lateral/medial convex points of the condyle and the horizontal contained angle were 128.34±8.68 mm, 88.69±6.75 mm and 145.87°±12.01°. Compared with preoperative design, the maximum deviation of the actual postoperative registration was 1.67±0.63, and the difference was not statistically significant (P>0.05).CONCLUSIONS: The application of 3D printing PLA guide plate in the segmental section and reconstruction of the mandible can effectively simplify the operation, and better reconstruct the continuity of the mandible. The surgical accuracy can fully meet clinical needs with relatively low prices.

oncology,medicine, research & experimental
[Application of Three Dimensional Model in Treatment of Superolateral Dislocation of Mandibular Condyle].

Xin Xu,Rong-xin Deng,Si-min Deng,Jun-lie Yang,Jun Chen

DOI: https://doi.org/10.3785/j.issn.1008-9292.2014.09.013

2014-01-01

Abstract:OBJECTIVE:To assess the application of three-dimensional jaw model in treatment of superolateral dislocation of condyle.METHODS:Nine patients with superolateral dislocation of condyle and symphyseal fractures were admitted in hospital from June 2008 to June 2013. Spiral CT scan on maxilla and mandible was performed，and three-dimensional jaw model was constructed with rapid prototyping technology. According to conditions of condylar superolateral dislocation model，the operation scheme was designed. The symphyseal fracture line was made and fracture was reduced on three-dimensional jaw model. Individualized prefabricated reconstructive titanium plate was made on symphyseal fracture model. Symphyseal fracture was replaced with individualized prefabricated mandibular reconstruction titanium plate according to occlusal relationship. At the same time，reduction of condylar superolateral dislocation was accomplished.RESULTS:Operations were successfully completed in 9 cases under guidance of three dimensional jaw model surgery. Operative incision was primarily healed，and occlusal relationship was restored. Postoperative CT scan showed that the locations of condyle in 9 cases were completely restored. Patients were followed-up for 6-28 months with a median of 18 months. The maximum of mouth opening was 3.1- 4.2 cm with a medians of 3.3 cm，and the occlusal relationship of all patients was normal after surgery.CONCLUSION:Three-dimensional jaw model can show complete status of condylar superolateral dislocation and symphyseal fracture. The model can accurately shape symphyseal reconstructive titanium plate and restore condylar superolateral dislocation during reductive surgery.
[A comparative study of the efficacy of customized titanium plates versus conventional maxillary protraction in the treatment of skeletal class Ⅲ patients]

F Wang,S Chang,S R Liang,C C Ren,X J Xie,Y X Bai

DOI: https://doi.org/10.3760/cma.j.cn112144-20240418-00158

2024-09-09

Abstract:Objective: To compare the clinical efficacy of customized titanium plate and conventional maxillary protraction treatment in patients with skeletal class Ⅲ malocclusion during growth spurt. Methods: During growth spurt, skeletal class Ⅲ patients with maxillary hypoplasia who were treated in the Department of Orthodontics, Capital Medical University School of Stomatology from August 2018 to July 2021 were prospectively enrolled. They were treated with maxillary protraction using customized titanium plates (customized titanium plate group) and conventional methods (conventional protraction group), respectively. Lateral cephalometric radiographs were collected before and after treatment for conventional cephalometric analysis, including SNA angle (angle between Sella, Nasion and A point), ANB angle (angle between A point, Nasion, and B point), FH-MP angle (mandibular plane angle), Y-axis angle, U1-L1 angle (upper to lower central incisor angle), U1-SN angle (upper incisor to SN plane angle), anterior and lower height, maxillary length, etc. The stable basicranial line (SBL) was used as the reference line to measure the distance from each reference point (ANS point, A point, Prn point, Sn point, UL point etc.) to the stable basicranial vertical line (VerT, the perpendicular line of the skull base line at the intersection point of the anterior wall of the sella image and the inferior edge of the anterior bed process). Paired t-tests were performed on the cephalometric data before and after maxillary protraction treatment in the two groups, and two independent samples t-tests were performed to compare the differences in the efficacy of the two maxillary protraction methods. Results: A total of 20 patients (9 males and 11 females), aged (10.8±1.3) years, were included in the personalized titanium plate group. A total of 20 patients (8 males and 12 females), aged (10.5±1.1) years, were included in the conventional protraction group. The SNA angle, ANB angle, FH-MP angle, Y-axis angle, anterior lower height, maxillary length, ANS-VerT distance, A-VerT distance, Prn-VerT distance, Sn-VerT distance, and UL-VerT distance were significantly higher than those before treatment in the two groups (P<0.05). The changes of SNA angle, ANB angle and A-VerT before and after treatment in the personalized titanium plate group [3.15°±2.28°, 4.64°±1.40°, (4.41±3.43) mm, respectively] were significantly higher than those in the traditional group [2.13°±2.69°, 2.81°±1.10°, (3.13±4.76) mm, respectively](P<0.05), and the changes of U1-L1 angle and U1-SN angle before and after treatment (-0.76°±7.42° and 1.74°±6.38°, respectively) was significantly lower than that of the control group (-5.14°±6.62° and 4.57°±5.24°, respectively, P<0.05). Conclusions: Maxillary protraction can effectively improve skeletal class Ⅲ relationships in growing patients. The linear measurements using the SBL line as a reference plane visualize the sagittal improvement in sagittal relationship after maxillary protraction. The customized titanium plate maxillary protraction treatment has a clear therapeutic effect on patients with skeletal class Ⅲ deformities, and its dental effect is relatively small.
[Development and clinical application of custom-made temporomandibular joint-skull base combined prosthesis]

J S Zheng,X Wei,Z X Jiao,X H Liu,M J Chen,W B Jiang,C Yang

DOI: https://doi.org/10.3760/cma.j.cn112144-20210412-00169

2021-07-09

Abstract:Objective: To introduce the design, manufacture and clinical application of the custom-made temporomandibular joint (TMJ)-skull base combined prosthesis and evaluate its safety, effectiveness and accuracy. Methods: The patients diagnosed with the TMJ-skull base lesion in Department of Oral Surgery, Shanghai Ninth People's Hospital from October 2016 to November 2020 were recruited in this study. The maxillofacial CT data for all the patients were obtained and transformed into the Mimics 18.0 software preoperatively. The custom-made TMJ-skull base combined prosthesis, included four components, was designed based on the anatomy, stress distribution and movement of the TMJ and skull base, and fabricated by three-dimensional printing and 5-axis milling technologies. The TMJ-skull base lesion was excised completely with the help of digital templates from modified preauricular and/or post and submandibular incisions. The combined prosthesis were implanted and fixed after the lesion resection. The examinations including general situation, cranio-maxillofacial structure and function were taken during and after surgery to assess its using effect. Results: Ten patients [6 females and 4 males, (43.2±13.6) years old] were included and all prostheses were positioned accurately and fixed excellently. After (29.4±17.3) months follow-up, the occlusion relationship was stable and no adverse symptoms such as dizziness, headache, meningeal irritation and permanent facial nerve injury occurred. The pain, diet, mandibular movement function, lateral movement to diseased side and mouth opening had significant improvements. The forward movement and lateral movement to normal side were not improved significantly. There were no prosthesis displacement, loosening and fracture in X-ray and CT postoperatively. With the pre and postoperative craniomaxillofacial model merging, the maximal implanted error was (0.52±0.17) mm for fossa and condyle and (1.62±0.26) mm for skull base and mandibular handle in surface deviation analysis. Conclusions: The custom-made TMJ-skull base combined prosthesis with customized design and 3D printing fabrication is safe, effective and precise in clinical application.
Patient-specific plates for facial fracture surgery: A retrospective case series

Ran-Yeong Cho,Soo-Hwan Byun,Sang-Yoon Park,Sung-Woon On,Jong-Cheol Kim,Byoung-Eun Yang

DOI: https://doi.org/10.1016/j.jdent.2023.104650

Abstract:Objectives: Surgeons often encounter challenges when treating maxillofacial fractures using conventional methods that involve trimming or bending ready-made titanium plates for open reduction and internal fixation (ORIF) since it can be time-consuming, imprecise, and inconvenient. This retrospective case series aimed to introduce a novel bone reduction method that utilizes virtual planning, patient-specific surgical guides, and titanium plates. Methods: Seven patients with mandibular symphysis or subcondylar fractures resulting from facial trauma underwent cone-beam computed tomography (CBCT) or facial CT scans, and their medical histories were documented. Virtual surgery was conducted based on three-dimensional (3D) stereolithography images derived from CT scans using the FaceGide software (MegaGen, Daegu, Korea). ORIF was performed using patient-specific surgical guides and plates that were designed, printed, and milled. Radiographic, clinical, and occlusal evaluations were conducted at two weeks and six weeks postoperatively. Subsequently, 3D images from virtual surgery and postoperative CT scans were compared. Results: The comparison of 3D virtual surgery and postoperative images revealed minimal surface differences of less than 1 mm. T-scan evaluations indicated that there were no statistically significant differences between the two- and six-week postoperative assessments. Favorable clinical outcomes were observed. Conclusion: This novel method demonstrated stable outcomes in terms of occlusion and healing, with no notable complications. Consequently, this approach may serve as a viable alternative to conventional methods. Clinical significance: Facial fracture surgery that utilizes patient-specific surgical guides and plates within a digital workflow can facilitate meticulous surgical planning, reducing the risk of complications and minimizing operation time.

Selenium concentrations in maternal and umbilical cord blood at 24-42 weeks of gestation: basis for optimization of selenium supplementation to premature infants.

[Application of Computer Aided Design-Computer Aided Manufacture Technique in Mandible Defect Reconstruction with Individual Titanium Prosthesis].

[Application of Computer Aided Design/computer Aided Manufactured Techniques in Mandible Defect Reconstruction].

Simultaneous correction of bilateral temporomandibular joint ankylosis with mandibular micrognathia using internal distraction osteogenesis and 3-dimensional craniomaxillofacial models.

Application of CAD/CAM Techniques in Mandible Large-Scale Defect and Reconstruction with Vascularized Fibular Bone Graft

[Application of Three-Dimensional Printing Technique in Repair and Reconstruction of Maxillofacial Bone Defect].

THE APPLICATION OF RAPID PROTOTYPING IN THE ORTHOGNATHIC SURGERY

The use of modified 3D-printed reconstruction plates in mandible segmental defect rehabilitation: a case report

Outcome Evaluation of Three-Dimensionally Printed Patient-Specific Surgical Plates for Mandibular Reconstruction

Application of 3D printed titanium mesh and digital guide plate in the repair of mandibular defects using double-layer folded fibula combined with simultaneous implantation

Application of a three dimensional digital model for mandibular plastic surgery

Technical Procedures for Template-Guided Surgery for Mandibular Reconstruction Based on Digital Design and Manufacturing

Application of Three-Dimensional Printing Technology in Osteotomy for Chin Width and Prominent Mandibular Angle

[Clinical application of virtual surgery combined with guide plate in reduction and fixation of condylar neck fracture in 7 patients]

Clinical Application of Computer-assisted Three-dimensional Reconstruction Combined with 3D Printing in Mandibular Defect Reconstruction

[Application of 3D printing technology under three-dimensional reconstruction in mandibular reconstruction].

Clinical application and accuracy analysis of 3D printing guide plate based on polylactic acid in mandible reconstruction with fibula flap

[Application of Three Dimensional Model in Treatment of Superolateral Dislocation of Mandibular Condyle].

[A comparative study of the efficacy of customized titanium plates versus conventional maxillary protraction in the treatment of skeletal class Ⅲ patients]

[Development and clinical application of custom-made temporomandibular joint-skull base combined prosthesis]

Patient-specific plates for facial fracture surgery: A retrospective case series