Abstract:Background: Temporomandibular joint (TMJ) overloading is considered a primary cause of temporomandibular joint disorders (TMD). Accordingly, craniomaxillofacial structural parameters affect the loading situation in the TMJ. However, no effective method exists for quantitatively measuring the loading variation in human TMJs. Clinical statistics, which draws from general rules from large amounts of clinical data, cannot entry for exploring the underlying biomechanical mechanism in craniomaxillofacial system. The finite element method (FEM) is an effective tool for analyze the stress and load on TMJs for several cases in a short period of time; however, it is difficult to generalize general patterns through calculations between different cases due to the different geometric characteristics and occlusal contacts between each case. Methods: (1) This study included 88 subjects with 176 unilateral data to measure angle (α) of the distance to the plane of occlusion. The bone destruction score was evaluated for clinical statistics. To rule out effects of the potential factors and ensure the generality of the study, one participant with no obvious bone destruction was selected as the standard case for establishing the three-dimensional (3D) theoretical model and FEM. (2) Three groups of forces, including biting, muscles and joint reaction forces on mandible, were adopted to establish a 3D theoretical model. (3) By modifying the sagittal α and coronal three types of deviation angle (φ) of the original model, nine candidate models were obtained for the FEM studies. Results: (1) The static equilibrium equations, were used to establish a 3D theoretical model for describing the loading of the TMJ. The theoretical model was validated by monotonously modifying the structural parameter in comparison to two-dimensional theoretical models reported previously; (2) The force on the TMJ gradually decreased with α, and this trend was validated by both clinic statistics and FEM results; (3) The effects of the three types of deviation angle were different. The results of the case where only rotating biting forces were considered was consistent with clinical statistics, indicating that the side with lower α experiences higher TMJ load. (4) Changing the unilateral proportionality coefficients of biting and muscle force produced opposite effects, wherein the effects of the muscle force were stronger than those of the biting forces. Conclusions: A negative correlation was observed between the joint load and α. Among the three types of asymmetric deformities, occlusal deviations were the primary factors leading to TMD. Unilateral occlusion can result in a greater load on the ipsilateral joint and should be avoided when using the side corresponding to the TMD. This study provides a theoretical basis for the biomechanical mechanism of TMD and also enables the targeted mitigation and treatment of TMD through structural modification.

Biomechanical effects of mandibular deviation on the temporomandibular joint in patients with mandibular prognathism under incisal occlusion

The biomechanical effects of bimaxillary osteotomies to the patients with mandibular retraction under incisal clenching

Temporomandibular joint stress analysis of patients with different mandibular deformities during unilateral molar occlusion

Effect of sagittal split ramus osteotomy on stress distribution of temporomandibular joints in patients with mandibular prognathism under symmetric occlusions

Effect of condylar rotation on the stress environment of the temporomandibular joint in patients with mandibular protrusion

Orthognathic Surgery Effects on Temporomandibular Joint Compressive Stresses.

Biomechanical behavior of temporomandibular joint movements driven by mastication muscles

Biomechanical behaviour of temporomandibular joints during opening and closing of the mouth: A 3D finite element analysis

Assessment of Masseter Volume and Postoperative Stability After Orthognathic Surgery in Patients With Skeletal Class III Malocclusion With Facial Asymmetry

Effect of occlusal contact on TMJ loading during occlusion: An in silico study

Three-dimensional theoretical model for effectively describing the effect of craniomaxillofacial structural factors on loading situation in the temporomandibular joint

Effects of the advanced mandibular spring on mandibular retrognathia treatment: a three-dimensional finite element study

Numerical investigation of the biomechanical effects of orthodontic intermaxillary elastics on the temporomandibular joint

Effect of Orthognathic Surgery on Pre-existing Temporomandibular Disorders

Three-dimensional analysis of hard and soft tissue changes in skeletal class II patients with high mandibular plane angle undergoing surgery

[Evaluation of Mandibular Stability and Condylar Volume after Orthognathic Surgery in Patients with Severe Temporomandibular Joint Osteoarthrosis].

Changes in masseter muscle morphology after surgical-orthodontic treatment in patients with skeletal Class III malocclusion with mandibular asymmetry: The automatic masseter muscle segmentation model

Three-dimensional finite element analysis of the TMJ and the mandible under orthopedic chincup forces

Three-dimensional finite element analysis of unilateral mastication in malocclusion cases using cone-beam computed tomography and a motion capture system

Stress distribution of the modified clear twin-block aligner on the temporomandibular joint, alveolar bone and teeth: A finite element analysis

Biomechanical study of temporomandibular joints of patients with temporomandibular disorders under incisal clenching: A finite element analysis