Abstract:The current understanding of the active layer morphology in ternary organic solar cells (OSCs) is superficial owing to more variables and complexity compared to that of binary OSCs. The PTB7-Th:PF12TBT:PC71BM ternary system with complementary polymer absorption spectra and efficient energy transfer from PF12TBT to PTB7-Th was anticipated to have an outstanding performance. However, only a limited improvement in the power conversion efficiency (PCE) was achieved when the ternary devices were processed from CB/DIO. This is because large PC71BM domains formed with the addition of amorphous PF12TBT and the PF12TBT molecules embedded in the large PC71BM domains served as trap sites. Constraining the formation of large PC71BM domains and avoiding PF12TBT molecules being fully embedded in PC71BM domains are needed for a better performance. Polymer pre-aggregation before liquid-liquid phase separation is beneficial to construct bicontinuous interpenetrating networks with proper phase-separated domains. Therefore, para-xylene was introduced into CB/DIO to cause a weak polymer-solvent interaction for enhanced PTB7-Th solution-phase aggregation. The enhanced PTB7-Th aggregation in the CB/PX/DIO solution restricted the extent of the liquid-liquid phase separation, and a well-developed polymer network formed with improved PTB7-Th crystallinity, which prevented large PC71BM domains from forming via fluid-phase Ostwald ripening in the liquid-solid phase separation stage. The appearance of PF12TBT emission and increased PTB7-Th emission in the ternary film processed from CB/PX/DIO suggested that fewer PF12TBT molecules were embedded in the PC71BM domains, and the energy transfer from PF12TBT to PTB7-Th was more efficient. Thus, PCE increased from 8.09% for binary blends processed from CB/DIO to 9.28% for ternary blends processed from CB/PX/DIO.

Toward Efficient Polymer Solar Cells with Thick Bulk Heterojunction by Introducing Iridium Complex As an Aggregation Reshaping Auxiliary

Over 18.2% efficiency of layer-by-layer all-polymer solar cells enabled by homoleptic iridium(III) carbene complex as solid additive

Design, Application, and Morphology Study of a New Photovoltaic Polymer with Strong Aggregation in Solution State

Improved Efficiency and Stability in Polymer Solar Cells Using a Tetra-nuclear Zinc(II) Complex Interfacial Layer

Largely improved bulk-heterojunction morphology in organic solar cells based on a conjugated terpolymer donor via a ternary strategy

Revealing Morphology Evolution in Highly Efficient Bulk Heterojunction and Pseudo‐Planar Heterojunction Solar Cells by Additives Treatment

Improved Hole Transfer and Charge Generation in All-Polymer Photovoltaic Blends with a P–i–N Structure

Ternary All‐Polymer Solar Cells with Efficiency up to 18.14% Employing a Two‐Step Sequential Deposition

Restricting The Liquid-Liquid Phase Separation Of Ptb7-Th:Pf12tbt:Pc71bm By Enhanced Ptb7-Th Solution Aggregation To Optimize The Interpenetrating Network

Performance improvement of polymer solar cells with binary additives induced morphology optimization and interface modification simultaneously

Influence of Molecular Geometry of Perylene Diimide Dimers and Polymers on Bulk Heterojunction Morphology Toward High‐Performance Nonfullerene Polymer Solar Cells

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

Improved photon-to-electron response of ternary blend organic solar cells with a low band gap polymer sensitizer and interfacial modification

Morphology control by tuning electrostatic interactions for efficient polythiophene-based all-polymer solar cells

Toward Efficient Triple-Junction Polymer Solar Cells Through Rational Selection of Middle Cells

Realizing 19.05% Efficiency Polymer Solar Cells by Progressively Improving Charge Extraction and Suppressing Charge Recombination

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

Bulk heterojunction perovskite solar cells incorporated with p-type low optical gap conjugated polymers

Efficient ternary blend polymer solar cells with indene-C60 bisadduct as an electron-cascade acceptor

Multiple Functionalities of Polyfluorene Grafted with Metal Ion-Intercalated Crown Ether As an Electron Transport Layer for Bulk-Heterojunction Polymer Solar Cells: Optical Interference, Hole Blocking, Interfacial Dipole, and Electron Conduction.