Abstract:A new selective catalytic reduction (SCR) system for captive power plants in the petrochemical industry was analyzed. The key components suitable for the target SCR system were obtained using computational fluid dynamics (CFD) numerical simulation combined with a cold physical model. The structural characteristics of the SCR system were studied, and corresponding design schemes were obtained for the key components, such as the guide plate, the ammonia injection grid (AIG), the static mixer, and the rectifier grille. The distributions of the flue gas velocity and the NH3 concentration within the flue cross-section in front of the first layer catalyst were studied in detail. Synchronously, the pressure loss and the temperature reduction characteristics in the SCR system were also considered. CFD results showed that the average standard deviation of the flue gas velocity was about 11.61%, and the average standard deviation of the NH3 concentration distribution could reach about 3.79% under the five operating conditions. It could be concluded that the uniformity of the flue gas velocity and the NH3 concentration distribution within the above flue cross-section was guaranteed by comparing to the design standard of 15% and 5%, respectively. It was further found that the maximum pressure loss between the inlet and the first layer catalyst was about 106.64 Pa, and the temperature reduction characteristic of the entire SCR system could be maintained within ±0.01 °C, which indicated that no extreme adverse effect arose due to the introduce of the key components. The cold physical model experiment was accordingly conducted to verify the reliability of the above CFD results. The cold physical model experiment results showed that the average standard deviation of flue gas velocity was about 8.82%, and the average standard deviation of NH3 concentration distribution could reach about 4.21%. The maximum biases for the standard deviations of the flue gas velocity and the NH3 concentration distribution were approximately 4.83% and 1.18% under the five operating conditions. Based on the good agreement of the research results via the two different methods, the designed key components of a new SCR system could be confirmed to be feasible, which would benefit the deNOx performance of the SCR system.

Predictor and Optimizer System on Selective Catalytic Reduction of NO in Activated Carbons Based on Experiment and Computational Intelligence Technique

Model Predictive Control Case Study: Selective Catalytic Reduction (scr) System in Coal-Fired Power Plant

Investigation on an Innovative Sorption System to Reduce Nitrogen Oxides of Diesel Engine by Using Carbon Nanoparticle

The Prediction of Spark-Ignition Engine Performance and Emissions Based on the SVR Algorithm

Optimization Analysis of Various Parameters Based on Response Surface Methodology for Enhancing NOx Catalytic Reduction Performance of Urea Selective Catalytic Reduction on Cu-ZSM-13 Catalyst

A simulation study on NOx reduction efficiency in SCR catalysts utilizing a modern C3-CNN algorithm

Dynamic NOX emission concentration prediction based on the combined feature selection algorithm and deep neural network

Multi-objective optimization of Fe-based SCR catalyst on the NO x conversion efficiency for a diesel engine based on FGRA-ANN/RF

Modeling NOx emissions from coal-fired utility boilers using support vector regression with ant colony optimization

Dynamic Prediction Model for NOx Emission of SCR System Based on Hybrid Data-driven Algorithms

Prediction and Control of the Nitrogen Oxides Emission for Environmental Protection Goal Based on Data-Driven Model in the SCR De-Nox System

Compact Research for Maritime Selective Catalytic Reduction Reactor Based on Response Surface Methodology

Nonlinear Dynamic Soft-Sensing Modeling of NOx Emission of a Selective Catalytic Reduction Denitration System

Development and verification of model predictive control strategy for selective catalytic reduction with rapid prototyping

CFD analysis of influencing factors on SCR denitration efficiency of sintering flue gas based on response surface methodology

Combining Support Vector Regression and Ant Colony Optimization to Reduce NOx Emissions in Coal-Fired Utility Boilers

Application of Scaleable Chaotic Ant Colony Algorithm in NO_x Emissions Optimization

Design and Verification of Key Components of a New Selective Catalytic Reduction System in a Petrochemical Captive Power Plant

Parameter optimisation of marine four-stroke engine EGR systems using RSM and NSGA-III

Physical and Chemical Process Model of SCR and Its Verification