Abstract:The geometry of a solar cavity receiver affects the absorption of incident solar energy and the temperature distribution on the absorber tube panels, and hence affects the operation stability and efficiency of the solar receiver. A modified combined computational method was proposed to investigate the thermal performance of the three dimensional (3-D) molten salt cavity models in steady state. This computational method was also used to calculate the thermal performance of the receiver in the Molten-Salt Subsystem/Component Test Experiment (MSS/CTE) in the United States, and the results agree well with published data. Molten salt cavity receivers with different heights were studied. The results show that a too-low or too-high height leads to low thermal efficiency of a receiver. Therefore, appropriate heights shall be chosen to enable receivers achieve relatively high efficiencies and reach low temperatures. The molten salt cavity receivers with different cross-sections in the chosen heights were then studied, to obtain a high-efficiency cavity receiver structure without increasing the inner surface area or the depth of the cavity, under the condition that the molten salt cavity receivers were in the same perimeter of the cross-section, aperture size, cavity height, tube panel and fluid flow layouts but different cavity depths. When-only the lengths of the back walls next to the side walls had been increased, the thermal efficiency decreased first and then increased with the depth decreasing, which reached the lowest value when the depth was 2.71 m. When the depth of the modified receiver is small enough, its thermal efficiency can be higher than that of the MSEE receiver. When only the lengths of the two walls adjacent to the aperture had been increased, the thermal efficiency increased with the depth decreasing, and was always higher than that of the receiver in the Molten-salt Electric Experiment (MSEE) in the United States. The thermal efficiency difference between the two arrangements of the side walls decreased with a decrease in the cavity depth. The cross-section of the MSEE receiver is similar to that of the receiver in the molten salt electric experiment by Sandia National Laboratories. Under the condition of side-on wind at a velocity of 8.3 m/s, the thermal efficiency of the modified cavity with the minimum depth is 2% higher than that of the MSEE cavity with the maximum depth. The convective heat loss is 3.1% lower, while the radiative and reflective heat losses changed slightly. Therefore, the modified cavity in the present study is capable of achieving a higher efficiency with a less depth. (C) 2017 Elsevier Ltd. All rights reserved.

Experimental Investigation of Thermal Performance Enhancement of Cavity Receiver with Bottom Surface Interior Convex

Optical efficiency analysis of cylindrical cavity receiver with bottom surface convex

Heat Loss Reduction Approach in Cavity Receiver Design Based on Performance Investigation of a Novel Positive Conical Scheme

Experimental Study on Thermal Performance of a Water/steam Cavity Receiver with Solar Simulator

Thermal performance analysis of a novel Conical-Cylindrical-Conical cavity receiver for a Scheffler concentrated solar system

An experimental investigation on thermal and optical analysis of cylindrical and conical cavity copper tube receivers design for solar dish concentrator

Experimental investigation on heat-transfer characteristics of a cylindrical cavity receiver with pressurized air in helical pipe

Design, Simulation and On-Sun Experiments of a Modified Sliding-Bed Particle Solar Receiver for Coupling with Tower Concentrating System

Experimental and Theoretical Analysis on a Linear Fresnel Reflector Solar Collector Prototype with V-shaped Cavity Receiver

Study On Trough Receiver For Linear Concentrating Solar Collector

An optimized model and test of the China’s first high temperature parabolic trough solar receiver

Experimental Study Of The Thermal Performance Of Solar Cavity Receiver During Start-Up Process

Simulation of Optical Performance for a Solar Cavity Receiver Arranged with Spiral Tubes

Theoretical and Experimental Analysis on Efficiency Factors and Heat Removal Factors of Fresnel Lens Solar Collector Using Different Cavity Receivers

Numerical Study on Thermal Performance of a Solar Cavity Receiver with Different Depths

Solar-thermal conversion investigation using surface partition method for a cavity receiver with helical pipe

Performance Investigation on a Linear Fresnel Lens Solar Collector Using Cavity Receiver

The Numerical Investigation on Optical Efficiency and Heat Flux Distribution of Conical Cavity Receiver

Numerical Investigation on the Thermal Performance of Molten Salt Cavity Receivers with Different Structures

Performance Investigation on Solar Thermal Conversion of A Conical Cavity Receiver Employing A Beam-Down Solar Tower Concentrator

Experimental and Theoretical Evaluation on the Thermal Performance of a Windowed Volumetric Solar Receiver