Abstract:Plastic deformation may occur in a mechanical structure during its manufacturing and service process, and may cause serious problem in the structural integrity. Therefore, a reliable pre-service or in service quantitative non-destructive evaluation (NDE) of plastic deformation is very important especially for a structure after suffering giant load such as a large earthquake. However, there is still no satisfactory method being established for the quantitative NDE of plastic deformation in key structures such as those of a nuclear power plant. For this purpose, three electromagnetic NDE methods, i.e., Magnetic Barkhausen Noise (MBN), Magnetic Incremental Permeability (MW) and Magnetic Flux Leakage (MFL) method are studied via experiments in this paper to investigate their feasibility for evaluation of plastic deformation in carbon steel SS400. A special testing system integrated these three electromagnetic NDE methods is established to measure the magnetic property of test-pieces with different plastic deformation, which was introduced by a tensile testing machine. It is found that the measurement signals of all these three methods have clear correlation with the plastic strains and show coincident tendency, which reveals the validity of these methods for the quantitative evaluation of plastic deformation. Among these methods, the MFL signals are of higher stability and repeatability but of relative low spatial resolution. The MBN method can give better resolution but of bigger standard deviation and is also not valid to evaluate a plastic strain of large scale. On the other hand, the MIP signals are more sensitive to the liftoff of sensor and to the remanent magnetization status, i.e. of more noise. Therefore, to measure the feature parameters of these three methods at the same time with an integrated testing system and to evaluate the plastic strain through signal fusion may give a better detectability and evaluation precision.

Joint Effect of Residual Stress and Plastic Deformation on Pulsed Eddy Current Response Signals in 304 Austenitic Stainless Steel

Distinguishing Evaluation of Plastic Deformation and Fatigue Damage Using Pulsed Eddy Current Testing

Evaluation of Plastic Deformation and Characterization of Electromagnetic Properties Using Pulsed Eddy Current Testing Method

Evaluation of Plastic Deformation in an Austenitic Stainless Steel based on Nonlinear ECT Method

Investigation of Electromagnetic Properties of 304 Austenitic Stainless Steel with Plastic Deformation and Fatigue Damage and Microstructure Analysis

OS0101 Effect of Electropulsing on Recovery of Strain in Stainless Steel

Feasibility Investigation of NDE for Plastic Deformation in Biaxial Specimen using PECT Method

Achieving Stress Relief in Martensitic Stainless Steel Via High-Density Pulsed Electric Current Treatment

Realizing Strength–ductility Synergy in a Lean Duplex Stainless Steel Through Enhanced TRIP Effect Via Pulsed Electric Current Treatment

Creep-fatigue Properties and Deformation Mechanism of 316L Steel Fabricated by Laser Powder Bed Fusion (PBF-LB/M)

Reconstruction of Stress Corrosion Cracks Using Signals of Pulsed Eddy Current Testing

Dependence Of Deformation-Induced Magnetic Field On Plastic Deformation For Sus304 Stainless Steel

Influence of Plastic Deformation and Fatigue Damage on Electromagnetic Properties of 304 Austenitic Stainless Steel

A Study on Influence of Plastic Deformation on the Global Conductivity and Permeability of Carbon Steel

Quantitative Nondestructive Evaluation of Plastic Deformation in Carbon Steel Based on Electromagnetic Methods

Influence of Laser Peening Parameters on Residual Stress Field of 304 Stainless Steel

Effects of Welding and Constraint Conditions on the Welding Residual Stress and Hardness of Type 316 Stainless Steel Pipe

Stainless Steel Weld Defect Detection Using Eddy Current Pulsed Thermography

Simultaneous Evaluation of Residual Stress and Plastic Deformation in Ferromagnetic Steel by Using an Integrated NDE Method

Numerical Simulation of Residual Stress Field Induced by Ultrasonic Shot Peening

Residual Stress Field Induced by Laser Peening: a Finite Element Analysis