Abstract:The microstructure, stress rupture properties and deformation mechanisms of a new alloy during long-term aging were investigated. The microstructure evolution mainly included the coarsening of gamma' phase and the precipitation of eta phase. During aging at 700 degrees C, 750 degrees C and 800 degrees C, the coarsening rate k of gamma' phase was about 7.818 nm(3)/h, 42.927 nm(3)/h and 178.226 nm(3)/h, respectively. The activation energy Q for gamma' coarsening was about 279.98 kJ/mol, which meant that element diffusion controlled the coarsening of gamma' phase. After aging at 750 degrees C for 3000 h and 800 degrees C for 2000 h, a new needle-like eta phase was precipitated near GBs and around MC carbides, then grew into the grain interiors. The quantity of eta phase increased with the increase of aging time. With the growth of eta phase, gamma' depleted zones were found around eta phase. This was principally because both gamma' phase and eta phase were enriched in Ni and Ti, and the growing up of I phase absorbed gamma' phase. After aging at 700 degrees C for 300-3000 h and 750 degrees C for 300-2000 h, the stress rupture life at 750 degrees C/430 MPa remained at a high level and most of them were higher than 100 h. That was because the slightly grown-up gamma' phase acted as strong obstacles to the dislocation motion, Orowan bypassing combing stacking fault shearing acted as the dominant mechanism during stress rupture deformation. After aging at 750 degrees C and 800 degrees C for 3000 h, the stress rupture life decreased to 45.7 h and 7.68 h, respectively. One reason was that the seriously grown-up gamma' phase was very hard to impede the dislocation motion, almost all gamma' phases were cut by dislocations with leaving stacking faults inside them during stress rupture deformation. The other reason was that needle-like eta phase promoted dislocation pile-up and contributed to the nucleation of micro-cracks, meanwhile the gamma' depleted zones could be conductive to the propagation of micro-cracks.

Effects Of The Gamma ''-Ni3nb Phase On Fatigue Behavior Of Nickel-Based 718 Superalloys With Different Heat Treatments

Effects of the γ″-Ni 3 Nb Phase on Mechanical Properties of Inconel 718 Superalloys with Different Heat Treatments.

Effects of the "-Ni<sub>3</sub>Nb Phase on Mechanical Properties of Inconel 718 Superalloys with Different Heat Treatments

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

Effects of the γ″-Ni3Nb Phase on Mechanical Properties of Inconel 718 Superalloys with Different Heat Treatments

Mechanical Properties of Micro-phases Along < 001 > Direction of Directionally Solidified Nickel-base Super-alloy by In-situ Nano-Indentation

Fracture Mechanisms Induced by Microporosity and Precipitates in Isothermal Fatigue of Polycrystalline Nickel Based Superalloy

Effect of Long-Term Aging on the Microstructure, Stress Rupture Properties and Deformation Mechanisms of a New Cast Nickel Base Superalloy

Elevating Fatigue Life in Nickel-Based Superalloys Through Suppression of Persistent Slip Bands/markings Via High-Density Pulsed Electric Current Treatment

Effect Of Heat Treatment Process On Microstructure And Fatigue Behavior Of A Nickel-Base Superalloy

The Effect of Long-Term Aging on the Microstructure and Properties of a Novel Nickel-Based Powder Superalloy FGH4113A

Effect of Solution Aging Treatment on High and Very High Cycle Fatigue Properties of Nickel-Based Alloy Fabricated by Laser Powder Bed Fusion at 25 °C and 650 °C

Effect of the Δ Phase on the Tensile Properties of a Nickel-Based Superalloy

Effect of Heat Treatment on High-Temperature Low-Cycle Fatigue Behavior of Nickel-Based GH4169 Alloy

Influence of Heat Treatment on Cyclic Response of Nickel-Based Superalloy Inconel 718 up to Very-High Cycle Regime

The Effects of Inhomogeneous Microstructure and Loading Waveform on Creep-Fatigue Behaviour in a Forged and Precipitation Hardened Nickel-Based Superalloy

The Precipitation Behavior Effect of Δ and Γ" Phases on Mechanical Properties of Laser Powder Bed Fusion Inconel 718 Alloy

Evolution of microstructure and δ phase in an aging-treated nickel-based superalloy during hot compression

New insights into the stress rupture life enhancement mechanisms of a nickel-based superalloy

Influence of Heat Treatment on Microstructure and Stress Rupture Property of Nickel-base Superalloy

Effect of heat treatment on the microstructural evolution of a nickel-based superalloy additive-manufactured by laser powder bed fusion