Abstract:The temperature evolution, stress evolution, and dendrite growth during the laser metal deposition (LMD) process of Inconel 718 alloy were simulated using a multi-scale model that combines the finite element method and the Cellular Automata (CA) method. This model established the relationship between the thermal behavior of the molten pool and the solidification characteristics, and predicted the morphological size of the solidified structure. Research indicates that under conditions of higher cooling rate and lower shape control factor, equiaxed grains are prone to form, with a lower degree of elemental segregation in this region, which is conducive to the precipitation of granular Laves phase. Conversely, under conditions of lower cooling rate and higher shape control factor, columnar grains are more likely to form, with a higher degree of elemental segregation in this region, leading to the precipitation of chain-like Laves phase. The results of thermo-mechanical coupled simulation suggest that the maximum transient thermal stress is located at the overlap position, and when the component cools down to room temperature, the maximum normal stress along the scanning direction is observed. Dendritic growth results demonstrate that during the equiaxed grain growth process in the top region of the melt pool, the released solute is constrained by time and space, leading to the accumulation of solute and the formation of interdendritic segregation. In areas with a higher grain density, the solute accumulation zones overlap, resulting in an increase in solute concentration, which inhibits dendrite growth. In the middle region of the melt pool, during the columnar grain growth process, the solute concentration in the gaps between adjacent grains continuously increases, resulting in micro-segregation phenomena. Experimental measurements have shown that the temperature field's melt pool morphology, stress values along the scanning path, and dendritic morphology are in good agreement with the experimental outcomes.

The Precipitation Behavior Effect of Δ and Γ" Phases on Mechanical Properties of Laser Powder Bed Fusion Inconel 718 Alloy

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Knowledge of process-structure-property relationships to engineer better heat treatments for laser powder bed fusion additive manufactured Inconel 718

Insight into Elongation and Strength Enhancement of Heat-Treated LPBF Ni-based Superalloy 718 Using In-Situ SEM-EBSD

Microstructures and High-Temperature Mechanical Properties of Inconel 718 Superalloy Fabricated via Laser Powder Bed Fusion

Effect of heat treatment on microstructures and mechanical properties of Inconel 718 additively manufactured using gradient laser power

Microstructure and mechanical properties at elevated temperatures of as-built and heat-treated Inconel 718 produced through laser powder bed fusion processes

Study of pre-precipitated 8 phase promoting deformation twinning and recrystallization behavior of Inconel 718 superalloy during hot compression

Effect of heat treatment on microstructure, precipitation behavior and mechanical properties of Inconel 718 fabricated by laser direct energy deposition

Effect of homogenization and solution treatments time on the elevated-temperature mechanical behavior of Inconel 718 fabricated by laser powder bed fusion

Microstructural evolution and mechanical properties of IN718 alloy fabricated by selective laser melting following different heat treatments

Effect of heat treatment on microstructure and mechanical properties of selective laser melted Inconel 718 alloy

Microstructural evolution and mechanical properties of Inconel 718 alloy manufactured by selective laser melting after solution and double aging treatments

Microstructure and mechanical property comparison of Inconel alloys fabricated using micro and conventional laser powder bed fusion

Mechanical Characterization of Near-Isotropic Inconel 718 Fabricated by Laser Powder-Bed Fusion

Effects of a modified heat-treatment on microstructure and mechanical properties of additively manufactured Inconel 718

Dissolution of the Laves Phase and δ-Precipitate Formation Mechanism in Additively Manufactured Inconel 718 during Post Printing Heat Treatments

The δ Phase Precipitation of an Inconel 718 Superalloy Fabricated by Electromagnetic Stirring Assisted Laser Solid Forming

Effect of heat treatment on microstructural evolution and hardness homogeneity in laser powder bed fusion of alloy 718

Thermodynamic Behavior and Microstructure Evolution of Inconel 718 Alloy by Laser Metal Deposition

Effect of high preheating on the microstructure and mechanical properties of high gamma prime Ni-based superalloy manufactured by laser powder bed fusion