Abstract:A MoNx coating serves as an effective wear protection layer and is crucial for the investigation of its tribological characteristics at various temperatures. This study examined the tribological characteristics of MoNx coatings that were deposited through high-power pulsed magnetron sputtering (HiPIMS) in an Ar/N2 environment with varying N2 partial pressures. The microstructures and mechanical properties of the coatings were elucidated using scanning electron microscopy, grazing-incidence-angle X-ray diffraction, energy-dispersive spectroscopy, and nanoindentation. The dry friction performances of the coatings at different heating temperatures were studied using a ball-on-disk tribometer. The MoNx coating produced by HiPIMS was composed primarily of fcc−Mo2N and featured a fine, dense column crystal with a maximum hardness of 28.8 GPa. The MoNx coatings exhibited excellent lubrication and wear reduction properties at room temperature (RT). The dry friction performances of the MoNx coatings at elevated temperatures were expected to depend on the growth of the MoO3 tribolayer. At relatively low temperatures (300 °C and 400 °C), the MoO3 tribolayer grew slowly and was not enough to provide good lubrication, causing increases in the dry friction of the coatings. However, the δ−MoN phase formed in the MoNx coating deposited at a high N2 partial pressure could facilitate the formation of MoO3 and thus decreased the friction coefficient at 400 °C. At the relatively high heating temperature of 500 °C, however, the MoO3 tribolayer grew so rapidly that the oxide layer became thick, resulting in an increase in the wear rate. It is believed that tuning the growth rate of MoO3 via optimizing the composition and structure of the MoNx coatings might be a useful way to improve the dry friction at various elevated temperatures.

Influence of Mo contents on the tribological properties of CrMoN/MoS2 coatings at 25–700 °C

Investigation of the elevated temperature tribological property and wear mechanism of Fe‐15Cu‐0.8C materials containing Mo‐coated MoS2 powders

Excellent Tribological Performance at Elevated Temperatures and Associated Mechanisms of Novel AlCoCrFeNi-MoS2 Solid Self-Lubricating Composite

The Synergistic Effects Of Mo As An Alloy Element Added To Chromium Carbide Coatings On Their Lubrication Properties At High-Temperatures

Influence of Molybdenum Content and Load on the Tribological Behaviors of In-Situ Cr3C2-20 Wt % Ni Composites

Effect of MoS2 on the Tribological Properties of in Situ Fe3Al-20 Wt% Al2O3-4 Wt% Cr Composites

Study on the High Temperature Tribological Properties of Ni-Cr Based Alloys Containing MoS2

Improving high-temperature wear resistance of arc-evaporated AlCrN coatings by Mo alloying

Dependence of High Temperature Tribological Performance of Mos2-Based Composites on Type of Oxides

Effect of MoO3 on the Microstructure and Tribological Properties of Laser-Clad Ni60/nanoCu/h-BN/MoO3 Composite Coatings over Wide Temperature Range

Dry Friction Performances of MoNx Coatings Deposited by High−Power Pulsed Magnetron Sputtering

Microstructure and tribological properties evolution of Ni-Mo-SrSO 4 composites as a function of Mo contents at different temperatures

High temperature tribological behaviors and wear mechanisms of NiAl-MoO3/CuO composite coatings

Mo-doped Cr-Ti-Mo Ternary O-Max with Ultra-Low Wear at Elevated Temperatures

Study on Tribological Performances of MoS2 Coating at High Temperature

High Temperature Tribological Properties of Nano La2O3-Doped MoSi2 Composite Coatings Sintered in Vacuum

Structural, mechanical and tribocorrosion performances of CrMoSiN coatings with various Mo contents in artificial seawater

Effect of Nano-ZrO2 on the Microstructure and High Temperature Tribological Properties of MoSi2 Coating

Tribological Performances of Graphite–mos2 Coating at Various High Temperatures

The influence of nano-CeO2 on tribological properties and microstructure evolution of Cr3C2-NiCrCoMo composite coatings at high temperature

Effect of Magnetron Sputtering on Microstructure and Tribological Properties of CrN-based Composite Coatings