Abstract:The basic structure of an organic light emitting device (OLED) is composed of a hole trans porting layer (HTL). a light-emitting layer, an electron transporting layer (ETL) , sandwiched between the anode and cathode. The operating mechanisms of the OLEDs involve the injection of electrons and holes from the electrodes, and electron-hole recombination which emits the light. Therefore, the efficiency of the carrier injecting has a great influence on the performance of the device. A variety of materials for both the anode and cathode, which has recently attracted strong attention is systematically studied, The mechanisms of the improvement of several anode treatments and a popular cathode structure are especially analyzed. For anode, a transparent and conducting thin film which is usually oxide can be adopted. And because the barrier height of the anode and the HTL decides the efficiency of the hole injecting, the maten al used as anode should also attain a high work function. Then indium-tin-oxide (ITO) is a better choice and has been used more widely, compared with other materials. The work function of ITO thin film can be increased after oxygen-plasma, ultraviolet(UV) ozone, and aquaregia treatments. The reason is discussed of that, and consider that although three factors i.e.:. (1) C-containing contaminants, (ii) the O/In ratio, and (iii) the In/Sn ratio on the surface affect the work function, the first one is crucial. For a good treatment, the variation of the resistivity of ITO after it should also be taken into account, because a low volt age share of the anode would result in the reduction of the turn-on voltage. Similar to the hole injecting, the barrier height of the cathode and the ETL decides the efficiency of the electron injecting. But contrary to the anode, a low work function is preferable for the material as cathode. And a good chemical stability in air is also expected. Now the cathode with a structure metal/thin insulating layer maybe the idealest choice. Explanations have been put forward for the remarkable improvement of the special structure from several aspects i. e. : (i) tunneling effect, (ii) valence band bending, (iii) reduction of the quenching cen ters. and (iv) dipole mode. Through analysis, the first three aspects are more reasonable, and they are all responsible for the improvement, but with different contribution.

A NEW STRUCTURE OF FLEXIBLE OLED WITH COPPER NANOWIRE ANODE AND GRAPHERE OXIDE/PEDOT: PSS ANODE BUFFER LAYER

Flexible organic light-emitting devices with copper nanowire composite transparent conductive electrode

Solution-processed PEDOT:PSS:GO/Ag NWs composite electrode for flexible organic light-emitting diodes

Fabrication of Architectural Structured Polydopamine-Functionalized Reduced Graphene Oxide/carbon Nanotube/pedot:Pss Nanocomposites As Flexible Transparent Electrodes for OLEDs

Flexible Organic Light-Emitting Diodes with Poly-3,4-ethylene- Dioxythiophene As Transparent Anode

Effect of Graphene Oxide Doped Pedot:Pss As A Hole Injection Layer on the Luminescence Performance of Organic Light-Emitting Diodes

High-Performance Transparent PEDOT: PSS/CNT Films for OLEDs

Low-temperature nanowelding silver nanowire hybrid flexible transparent conductive film for green light OLED devices

High-Performance Copper Nanowire Electrode for Efficient Flexible Organic Light-Emitting Diode

Smooth ZnO:Al-AgNWs Composite Electrode for Flexible Organic Light-Emitting Device

Improved Performance of Organic Light-Emitting Diodes with MgF 2 As the Anode Buffer Layer

Improved Performances of Organic Light-Emitting Diodes with Metal Oxide As Anode Buffer

Flexible Organic Light-Emitting Diodes with ITO/Ag/ITO Multi-Layers As Anodes

Ultrasmooth, highly conductive and transparent PEDOT:PSS/silver nanowire composite electrode for flexible organic light-emitting devices

Transparent Electrodes Based on Ultrathin/ultra Smooth Cu Films Produced Through Atomic Layer Deposition As New ITO-free Organic Light-Emitting Devices

Highly Efficient Simplified Organic Light-Emitting Diodes Utilizing F4-TCNQ As an Anode Buffer Layer

The Application of Single-Layer Graphene Modified with Solution-Processed TiOx and PEDOT:PSS As a Transparent Conductive Anode in Organic Light-Emitting Diodes

Highly conductive sandwich-structured CNT/PEDOT:PSS/CNT transparent conductive films for OLED electrodes

Fabrication of nucleation induction layer of self-encapsulated metal anode by an atomic layer half-reaction for enhanced flexible OLEDs

The Study of Electrodes for Organic Electroluminescent Devices