Abstract:Summary form only given. Sintered Co(Cr)-MoB materials have a good combination of high modulus, high wear resistance, high corrosion resistance and adequate fracture toughness, making them suitable for many industrial applications such as metal-cutting tools and wear resistant components. In many applications, they are superior to oxide and carbide coatings. Recently, boride- based cermet surface coatings have been used to enhance the corrosion and wear resistance of various engineering components such as sink rolls and supporting bearings on a continuous galvanizing line (CGL). Many thermal spraying techniques such as air plasma spraying (APS) and high velocity oxy fuel (HVOF) spraying can be used to deposit the boride-based coatings. However, the coating properties depend strongly on the spraying technique. Compared to other spraying techniques, HVOF spraying is one of the best methods to deposit conventional boride-based cermet powders due to the very high velocities thereby flattening the particles into a denser and more wear-resistant coating. In this work, the microstructures and mechanical properties of the deposited Co(Cr)-MoB cermet coatings are investigated via SEM, TEM, XRD, MIP (Mercury intrusion porosimetry), tensile test and Vickers microhardness. The results show that the as-sprayed cermet coating main consists of ternary transition metal borides phases such as CoMo2B2 and CoMoB. The microstructure of the coating keeps unchanged compared with the starting powders and no reaction and interdiffusion occurs at the coating/substrate interface during HVOF spraying. The surface connected porosity of the as-sprayed cermet coating shows a typical bimodal pore size distribution. The adhesive strength of the Co(Cr)-MoB cermet coating decreases with increasing thickness of the as-sprayed cermet coatings, which is attributed to the residual stress induced during thermal spraying. The distributions of the microhardness values of the coatings are conducted by Weibull statistical means and the results reveal a bimodal distribution of Vickers microhardness values. Such distribution can be attributed to the presence of melted and unmelted phases in the resultant coating produced from the microstructured powder feedstock. The anisotropy in the mechanical properties between the cross section and the top surface of the cermet coatings is examined.

Effect Of Substrate Preheating On The Cermet Coating Structure Obtained Using Additive Technologies

Influence Of Substrate Preheating On The Structural And Phase Composition Of A Nickel-Based Cermet Coating

On the effects of B4C addition on the microstructure, mechanical properties, wear and thermal stability of TiCN- co -Cr3C2-Si3N4 cermets developed by vacuum hot pressing

Research On Wear Behavior Of Atc Cermet Material

In-Situ Synthesis of Metal Matrix Composite Coating with Laser Melting-Solidifying Processes

Effects of Substrate Preheating on Microstructure and Interface Characterization of Al2O3-13% TiO2 Ceramic Coating Fabricated by Laser Cladding

Pulsed Plasma Surfacing of Titanium Matrix Cermet Based on B4C

Microstructure and mechanical properties of b4c-tib2 composites reactive sintered from B4C + TiO2 precursors

Laser Cladding Ni-Base Composite Coating on Titanium Alloy with Pre-Placed B4C+NiCoCrAlY

Multi-ceramic phases synergistically reinforced titanium matrix composite coating deposited by laser cladding: Effect of B 4 C content on the microstructure and wear properties

Effect of Boronizing on Microstructure and Properties of Ti（ C, N）-based Cermet

Influence of the Reinforcement Phase Composition on the Structure and Abrasive Wear Resistance of Aluminum Matrix Composites Reinforced with B4C and SiC

EFFECT OF BORON CARBIDE CONCENTRATION ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES OF THE Ti-6Al-4V TITANIUM ALLOY PRODUCED BY SELECTIVE LASER MELTING

Microstructure and Mechanical Characterization of HVOF Sprayed Boride-Based Cermet Coatings

Laser Cladding NiCrBSi+2%B<sub>4</sub>C Coating on Ti-6Al-4V

Preparation and Enhanced Wear Resistance of HVAF-sprayed Fe-TiB2 Cermet Coating Reinforced by Carbon Nanotubes

Effect of Substrates Characteristics on Tribological Behaviors of AlTiN-Based Coated WC–Co Cemented Carbides

Influence of Preheating Temperature on Structural and Mechanical Properties of a Laser-Welded MMC Cobalt Based Coating Reinforced by TiC and PCD Particles

Effect of Boronizing on Thermal Shock Resistance of Ti( C, N)-based Cermet

The effect of substrate surface integrity on the surface properties of TiCrN coating applied via the CAE‐PVD method

Structure and tribological properties of super-hardened strengthening coatings based on boron carbide