Abstract:A pair of polymers, PBDTBT and PBDTDTBT, was synthesized for application in polymer solar cells (PSCs). Although these two polymers have similar absorption bands and molecular energy levels, PBDTDTBT exhibits much better photovoltaic performance in polymer solar cell (PSC) devices with power conversion efficiency (PCE) of 7.4%. To understand the differences between PBDTDTBT and PBDTBT, we have investigated the correlations of the molecular structure, morphology, dynamics and efficiency of these two polymers. A theoretical investigation using density functional theory (DFT) and time-dependent DFT (TDDFT) has been employed to investigate the electron density and electron delocalization extent of the unimers. TEM data showed that PBDTDTBT phase separates from PC71BM, while PBDTBT suffers from having a proper morphology on different processing conditions. Grazing incidence wide angle X-ray diffraction (GIWAXD) was used to probe the crystal structure of the polymers in thin film. A polymorph crystal structure was observed for PBDTBT. Grazing incidence small angle X-ray scattering (GISAXS) was used to probe the size scale of phase separation, with an optimized 25 nm feature size observed for PBDTDTBT/PC71BM blends, which agrees well with TEM results. Femtosecond transient absorption (TA) spectroscopy was used to probe the dynamics of the fundamental processes in organic photovoltaic (OPV) materials, such as charge separation and recombination. The enhanced absorption coefficient, good charge separation, optimal phase separation and higher charge mobility all contribute to the high PCE of the PBDTDTBT/PC71BM devices.

Morphology manipulation of photoactive layer through block copolymer to improve the photovoltaic performances of polymer solar cells

Optimizing the Morphology of All-Polymer Solar Cells for Enhanced Photovoltaic Performance and Thermal Stability

Improved Morphology and Efficiency of Polymer Solar Cells by Processing Donor–Acceptor Copolymer Additives

Enhancing the Photovoltaic Performance by Tuning the Morphology of Polymer:PC₇₁BM Blends with a Commercially Available Nucleating Agent.

Performance improvement of polymer solar cells with binary additives induced morphology optimization and interface modification simultaneously

Morphology Control Realizes Fast Charge Dissociation and Transport in High-Performance All-Polymer Solar Cells

Enhancement the photovoltaic performance of conjugated polymer based on simple head-to-head alkylthio side chains engineered bithiophene

19.10% Efficiency and 80.5% Fill Factor Layer‐by‐Layer Organic Solar Cells Realized by 4‐Bis(2‐thienyl)pyrrole‐2,5‐Dione Based Polymer Additives for Inducing Vertical Segregation Morphology

Design, Application, and Morphology Study of a New Photovoltaic Polymer with Strong Aggregation in Solution State

Engineering the Morphology Via Processing Additives in Multiple All-Polymer Solar Cells for Improved Performance

Manipulating backbone structure to enhance low band gap polymer photovoltaic performance

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

A Top‐Down Strategy to Engineer ActiveLayer Morphology for Highly Efficient and Stable All‐Polymer Solar Cells

Effect of solvent additive on active layer morphologies and photovoltaic performance of polymer solar cells based on PBDTTT-C-T/PC71BM

Vertical Distribution to Optimize Active Layer Morphology for Efficient All-Polymer Solar Cells by J71 As a Compatibilizer

Anthracene‐Assisted Morphology Optimization in Photoactive Layer for High‐Efficiency Polymer Solar Cells

Towards Efficient and Stable Organic Solar Cells: Fixing the Morphology Problem in Block Copolymer Active Layers with Synergistic Strategies Supported by Interpretable Machine Learning

Improving the Performance of Polymer Solar Cells by Altering Polymer Side Chains and Optimizing Film Morphologies

Improving Active Layer Morphology of All-Polymer Solar Cells by Dissolving the Two Polymers Individually

Improved Hole Transfer and Charge Generation in All-Polymer Photovoltaic Blends with a P–i–N Structure