Abstract:Morphology is one of the critical elements in determining the performance of polymer solar cells. As an important member in fullerene family, unsubstituted C-70 is scarcely employed to prepare polymer solar cells as compared with its derivatives, which is ascribed to its poor solution processability from a single organic solvent. Hereby, we show a method by using mixed solvent to prepare poly(3-hexylthiophene) (P3HT)/C-70 photoactive layer for high-performance polymer solar cells. Composite films spin coated from the solution with different mixed solvents are characterized by optical microscopy, transmission electron microscopy, UV-vis spectroscopy, and photovoltaic (PV) device characterization. As a result, heptane/o-dichlorobenzene (ODCB) mixture is found to be a good combination to prepare homogenous P3HT/C-70 film, and a high-performance device is thus obtained. By further optimizing the ratio between the donor P3HT and acceptor C-70 in the composite film, the PV cells with a power conversion efficiency of 2.24% have been achieved, which is much higher than that of the device prepared from ODCB-only solution. Dynamic light scattering measurement implies that C-70 molecules form aggregates with size of ~250 nm in ODCB solution, while in heptane/ODCB mixture, the aggregates are much smaller, which is responsible for the homogenous P3HT/C-70 film and also high device performance. This paper demonstrates a vivid approach to control the morphology of polymer solar cells, and thus significantly improved performance via deliberately designed solvent system for thin-film deposition.

Anthracene‐Assisted Morphology Optimization in Photoactive Layer for High‐Efficiency Polymer Solar Cells

Optimizing the Morphology of All-Polymer Solar Cells for Enhanced Photovoltaic Performance and Thermal Stability

Fine Optimization of Morphology Evolution Kinetics with Binary Additives for Efficient Non-Fullerene Organic Solar Cells

Additive-induced intermolecular interaction enhancement enables highly efficient organic solar cells

Synergistic Effect of Solvent and Solid Additives on Morphology Optimization for High-Performance Organic Solar Cells

High performance all-polymer solar cells enabled with solvent and solid dual additives

An Optimized Fibril Network Morphology Enables High‐Efficiency and Ambient‐Stable Polymer Solar Cells

Optimization Of Processing Solvent And Film Morphology To Achieve Efficient Non-Fullerene Polymer Solar Cells Processed In Air

Synergistic Control of Multilength-Scale Morphology and Vertical Phase Separation for High-Efficiency Organic Solar Cells

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

Crystallinity and Orientation Manipulation of Anthracene Diimide Polymers for All‐Polymer Solar Cells

Meniscus‐Assisted Coating with Optimized Active‐Layer Morphology toward Highly Efficient All‐Polymer Solar Cells

Improved Molecular Ordering in a Ternary Blend Enables All‐Polymer Solar Cells over 18% Efficiency

Revealing Morphology Evolution in Highly Efficient Bulk Heterojunction and Pseudo‐Planar Heterojunction Solar Cells by Additives Treatment

Enhanced Π–π Interactions of Nonfullerene Acceptors by Volatilizable Solid Additives in Efficient Polymer Solar Cells

Fine Tuning Miscibility of Donor/Acceptor through Solid Additives Enables All‐Polymer Solar Cells with 15.6% Efficiency

Morphology Control Realizes Fast Charge Dissociation and Transport in High-Performance All-Polymer Solar Cells

The Role of Morphology Control in Determining the Performance of P3HT/C-70 Bulk Heterojunction Polymer Solar Cells

A Top‐Down Strategy to Engineer ActiveLayer Morphology for Highly Efficient and Stable All‐Polymer Solar Cells

Fused‐Ring Core Engineering for Small Molecule Acceptors Enable High‐Performance Nonfullerene Polymer Solar Cells

Optimized Active Layer Morphology Toward Efficient and Polymer Batch Insensitive Organic Solar Cells