Abstract:BaTiO3/Ni0.5Zn0.5Fe2O4 (BTO/NZFO) ceramic composite exhibit giant permittivity and high permeability simultaneously and could be potentially used in electronic devices. In this work, the sol-gel in situ derived 0.1BTO/0.9NZFO ceramic composites were sintered by conventional ceramic method and a modified three-step sintering process. In the new method, the ceramic composite was sintered initially at 1310 degrees C for 12 h, then sintered at 1325 degrees C for only 5 min, and ultimately cooled down rapidly within about 10 seconds. XRD, SEM and EDS were performed to analyze the phase composition, observe the morphology, and identify the elemental distribution of the ceramic composite. Results showed that the composite can be successfully formed through a carefully controlled step-sintering and rapid-cooling process. The composite exhibits a denser microstructure with larger grain size and increased density (by about 10%) compared with those prepared by conventional ceramic method. The effective permittivity of the newly-prepared composite is larger than 270k below 100 kHz, 3.5 times larger than that conventionally sintered at 1310 degrees C. A relatively low loss (similar to 0.3) was obtained at 30 kHz, 10.6% lower than conventionally prepared samples. The effective permeability reaches 150 (increased by 16.8%) with low magnetic loss (similar to 0.02). The three-step sintering method is a new effective way to break through the limitation of conventional sintering method and prepare ceramic composites with high density and thus enhanced dielectric and magnetic properties.

High-performance colossal permittivity for textured (Al+Nb) co-doped TiO2 ceramics sintered in nitrogen atmosphere

Colossal Dielectric Permittivity in (al+nb) Co-Doped Ba0.4Sr0.6TiO3 Ceramics

Giant permittivity in (Nb0.5La0.5)xTi1‐xO2 ceramics prepared by slip casting in a strong magnetic field

Colossal Dielectric Performance of Pure Barium Titanate Ceramics Consolidated by Spark Plasma Sintering

Colossal Permittivity and Ultralow Dielectric Loss in Nb-doped SrTiO 3 Ceramics

Columbite-rich Multiphase TiO2 Nanoceramic with Superior Mechanical and Dielectric Properties

Colossal Permittivity Characteristics of (Nb, Si) Co-Doped TiO2 Ceramics

High Dielectric Permittivity and Ultralow Dielectric Loss in Nb-doped SrTiO3 Ceramics

Colossal permittivity and ultralow dielectric loss in SrTi1-Nb O3 ceramics sintered at different atmospheres via defect chemistry improvement

Enhanced Dielectric Performance of Niobium and Thulium Modified Rutile TiO2 Ceramics by Defect Regulation

High dielectric permittivity and ultralow dielectric loss in Nb-doped SrTiO 3 ceramics

Enhanced dielectric performance of Niobium and Thulium modified rutile TiO 2 ceramics by defect regulation

Colossal Permittivity and Low Dielectric Loss in Niobium and Europium Co-Doped TiO2 Ceramics by Adding B2O3

Colossal Dielectric Properties in (ta0.5al0.5)xti1−xo2 Ceramics

Giant Permittivity Up to 100 MHz in La and Nb Co‐doped Rutile TiO2 Ceramics

Formation and Electromagnetic Properties of 0.1 BTO/0.9NZFO Ceramic Composite with High Density Prepared by Three‐Step Sintering Method

Frequency and Temperature Independent (nb0.5ga0.5)x(ti0.9zr0. 1)1-Xo2 Ceramics with Giant Dielectric Permittivity and Low Loss

Enhanced dielectric properties and improved thermal stability in TiO 2 -based ceramics by Cu and Nb co-doping

Origin of Low Dielectric Loss and Giant Dielectric Response in (nb+al) Co‐doped Strontium Titanate

Origin of Colossal Dielectric Permittivity of Rutile Ti0.9In0.05Nb0.05O2: Single Crystal and Polycrystalline

Colossal Dielectric Permittivity in (al Plus Nb) Co-Doped Rutile Sno2 Ceramics with Low Loss at Room Temperature