Abstract:The successive approximation register (SAR) ADC is the most energy efficient architecture with moderate conversion rate and resolution. However, its comparator noise limits its resolution without sacrificing power efficiency. The delta-sigma modulator (DSM) is the most popular architecture for achieving high SNDR due to its oversampling, but the bulky operational amplifier (op-amp) makes it area inefficient. In LTE Advanced, the bandwidth (BW) of downlink ADCs needs to be configured according to the number of inter-band non-contiguous carrier aggregation (NCCA), which motivates us to combine the benefits of both architectures to reduce area and power consumption simultaneously with high SNDR. The noise-shaping SAR ADC [1] suppresses the comparison and quantization noise in signal BW using a simple cascaded FIR-IIR filter, which obviates the need for a power-hungry low-noise comparator or high-performance op-amp. To some extent, the noise-shaping SAR ADC is a hybrid of DSM and SAR ADCs. Hence, it has the potential to achieve the high resolution and good power efficiency of DSM and SAR ADCs, respectively. However, the passive sampling in an FIR filter introduces considerable thermal noise to the ADC, making it difficult to achieve a high SNR. This work presents an energy-efficient noise-shaping SAR ADC that uses a gain-enhanced dynamic amplifier and some capacitors to construct a low-noise dynamic FIR-IIR filter. The prototype achieves a peak SNDR of 79.74dB over a 5MHz BW with a power consumption of 0.46mW from a 1V supply.

A 20mhz Bandwidth Band-Pass Noise-Shaping SAR ADC with OPAMP Sharing Switched-Capacitor Filter

An 18-Bit 2MSPS SAR ADC with Double Passive Noise-Shaping Calibration

A Third-order Band-pass Fully-passive Noise-Shaping Modulator Based on a Time-interleaved SAR ADC

A 12-Bit ENOB 8mhz BW Noise-Shaping SAR ADC Using High-Speed Switches.

A Low Power Active-Passive Noise Shaping SAR ADC

A Configurable Noise-Shaping Band-Pass SAR ADC With Two-Stage Clock-Controlled Amplifier

A 16.5-μW 73.7-dB-SNDR Second-Order Fully Passive Noise-Shaping SAR ADC With a Hybrid Switching Procedure

An Area-Power-Efficient AFE with NS-SAR ADC for High-Frequency Ultrasound Applications

28.1 A 0.46mW 5MHz-BW 79.7dB-SNDR noise-shaping SAR ADC with dynamic-amplifier-based FIR-IIR filter

A 20 MHz Bandwidth 79 Db SNDR SAR-Assisted Noise-Shaping Pipeline ADC with Gain and Offset Calibrations

A Fully Dynamic Low-Power Wideband Time-Interleaved Noise-Shaping SAR ADC

A 0.0045 Mm2 31.5uw 312.5Khz-Bw 2Nd-Order Noise-shaping SAR ADC with a Dynamic-BulkSwitching Single-Transistor Amplifier

A Fully-Dynamic Time-Interleaved Noise-Shaping SAR ADC Based on CIFF Architecture.

A 68 uW 31 kS/s Fully-Capacitive Noise-Shaping SAR ADC with 102 dB SNDR

A 2.5-MHz BW, 75-dB SNDR Noise-Shaping SAR ADC With a 1st-Order Hybrid EF-CIFF Structure Assisted by Unity-Gain Buffer

A 250kHz-BW 93dB-SNDR 4th-Order Noise-Shaping SAR Using Capacitor Stacking and Dynamic Buffering

A 79dB-SNDR 167dB-FoM Bandpass ADC Combining N-Path Filter with Noise-Shaping SAR

A 93.6Db-Sndr 5Khz-Bw Fully Dynamic Hybrid CT-DT Noise Shaping SAR ADC

27.1 A 250kHz-BW 93dB-SNDR 4<sup>th</sup>-Order Noise-Shaping SAR Using Capacitor Stacking and Dynamic Buffering

A Second-Order Noise-Shaping SAR ADC with Passive Integrator and Tri-Level Voting

A 3.07 Mw 30 MHz-BW 73.2 Db-Sndr Time- Interleaved Noise-Shaping SAR ADC with Self-Coupling Second-Order Error-Feedforward