Abstract:The successive approximation register (SAR) ADC is the most energy efficient architecture with moderate conversion rate and resolution. However, its comparator noise limits its resolution without sacrificing power efficiency. The delta-sigma modulator (DSM) is the most popular architecture for achieving high SNDR due to its oversampling, but the bulky operational amplifier (op-amp) makes it area inefficient. In LTE Advanced, the bandwidth (BW) of downlink ADCs needs to be configured according to the number of inter-band non-contiguous carrier aggregation (NCCA), which motivates us to combine the benefits of both architectures to reduce area and power consumption simultaneously with high SNDR. The noise-shaping SAR ADC [1] suppresses the comparison and quantization noise in signal BW using a simple cascaded FIR-IIR filter, which obviates the need for a power-hungry low-noise comparator or high-performance op-amp. To some extent, the noise-shaping SAR ADC is a hybrid of DSM and SAR ADCs. Hence, it has the potential to achieve the high resolution and good power efficiency of DSM and SAR ADCs, respectively. However, the passive sampling in an FIR filter introduces considerable thermal noise to the ADC, making it difficult to achieve a high SNR. This work presents an energy-efficient noise-shaping SAR ADC that uses a gain-enhanced dynamic amplifier and some capacitors to construct a low-noise dynamic FIR-IIR filter. The prototype achieves a peak SNDR of 79.74dB over a 5MHz BW with a power consumption of 0.46mW from a 1V supply.

A 0.0045 Mm2 31.5uw 312.5Khz-Bw 2Nd-Order Noise-shaping SAR ADC with a Dynamic-BulkSwitching Single-Transistor Amplifier

An 18-Bit 2MSPS SAR ADC with Double Passive Noise-Shaping Calibration

A 13.5-ENOB, 107-μW Noise-Shaping SAR ADC With PVT-Robust Closed-Loop Dynamic Amplifier

A 625kHz-BW, 79.3dB-SNDR Second-Order Noise-Shaping SAR ADC Using High-Efficiency Error-Feedback Structure

A 3.07 Mw 30 MHz-BW 73.2 Db-Sndr Time- Interleaved Noise-Shaping SAR ADC with Self-Coupling Second-Order Error-Feedforward

A 78 dB 0.417 mW Second-Order NS SAR ADC with Dynamic Amplifier-Assisted Integrator

A 3.07mw 30Mhz-Bw 73.5Db-Sndr Time-Interleaved Noise-Shaping SAR ADC with 2Nd-Order Error-Feedforward and Redundancy-Bit Reduction

A 16.5-μW 73.7-dB-SNDR Second-Order Fully Passive Noise-Shaping SAR ADC With a Hybrid Switching Procedure

A 2.5-MHz BW, 75-dB SNDR Noise-Shaping SAR ADC With a 1st-Order Hybrid EF-CIFF Structure Assisted by Unity-Gain Buffer

A Second-Order Noise-Shaping SAR ADC with Passive Integrator and Tri-Level Voting

A 1.25-Mhz-bw, 83-Db SNDR Pipelined Noise-Shaping SAR ADC with MASH 2-2 Structure and Kt/c Noise Cancellation

A 13.8-ENOB Fully Dynamic Third-Order Noise-Shaping SAR ADC in a Single-Amplifier EF-CIFF Structure with Hardware-Reusing Kt/c Noise Cancellation

An 871 Nw 96.2 Db SNDR Pipelined Second-Order Noise-Shaping SAR ADC Employing Charge-Efficient CLS-Assisted Residue Amplifier

A 73-dB-SNDR 2nd-Order Noise-Shaping SAR With a Low-Noise Time-Domain Comparator

A 79.1Db-Sndr 20Mhz-Bw 2 Nd -Order SAR-Assisted Noise-Shaping Pipeline ADC with Gain and Offset Background Calibrations Based on Convergence Enhanced Split-Over-Time Architecture

28.1 A 0.46mW 5MHz-BW 79.7dB-SNDR noise-shaping SAR ADC with dynamic-amplifier-based FIR-IIR filter

A 13-ENOB Second-Order Noise-Shaping SAR ADC Realizing Optimized NTF Zeros Using the Error-Feedback Structure

A 20 MHz Bandwidth 79 Db SNDR SAR-Assisted Noise-Shaping Pipeline ADC with Gain and Offset Calibrations

A Low Power Noise-Shaping SAR ADC with Improved Integrator and Hybrid DAC Mismatch Mitigation Technique

A Configurable Noise-Shaping Band-Pass SAR ADC With Two-Stage Clock-Controlled Amplifier

A 12B-Enob 61µw Noise-Shaping SAR ADC with a Passive Integrator