Abstract:The noise-shaping (NS) SAR ADC is an emerging hybrid architecture that achieves high resolution and power-efficiency simultaneously by combining the merits of the SAR ADC and the AIADC, making it attractive to sensor readout and healthcare applications. To implement NS, most prior works adopted the classic cascaded integrator feed-forward (CIFF) structure for noise filtering [1-5]. Opamp-based integrators were used in [1-3] to achieve a relatively sharp noise transfer function (NTF), but at the cost of power and scaling friendliness. Reference [4] demonstrated 2 <sup>nd</sup> -order NS using fully passive switched-capacitor (SC) integrators, but has limited NS and thermal noise performance. Reference [5] combines passive SC filters with a dynamic amplifier (D-amp) to achieve good noise and power, but is vulnerable to process-voltage-temperature (PVT) variations. In addition, no prior NS SAR has realized complex NTF zeros for optimum NS. This presents a need for an NS SAR ADC that can combine optimized NTF, power efficiency and PVT robustness. To overcome the limitations of existing work, instead of adopting the CIFF structure, this paper presents a 2 <sup>nd</sup> -order NS SAR ADC using an error-feedback (EF) structure. It highlights the capability of realizing optimized complex NTF zeros by simply using charge sharing summation, a passive SC FIR and a comparator-reused dynamic amplifier with PVT tracking. This work achieves sharp NS performance while maintaining both hardware and power efficiency merits of the NS SAR with improved robustness. The prototype chip, fabricated in 40nm CMOS, achieves a 79dB SNDR at an OSR of 8 using a 9b SAR, resulting in a peak Schreier FoM of 178dB.

A 20khz 87.2db SNDR 12.1µw NS SAR ADC Based on Quantization-Error-Matched RLSB-First Algorithm

An 18-Bit 2MSPS SAR ADC with Double Passive Noise-Shaping Calibration

A 16-Bit 2.5-Ms/s SAR ADC with On-Chip Foreground Calibration

A 78 dB 0.417 mW Second-Order NS SAR ADC with Dynamic Amplifier-Assisted Integrator

A 13-Bit ENOB Third-Order Noise-Shaping SAR ADC Employing Hybrid Error Control Structure and LMS-Based Foreground Digital Calibration

A 73-dB-SNDR 2nd-Order Noise-Shaping SAR With a Low-Noise Time-Domain Comparator

A 62.5 Khz-Bw 92 Db-Sndr Noise-shaping SAR ADC with NS-CAL Method

A Second-Order Noise-Shaping SAR ADC with Passive Integrator and Tri-Level Voting

A Low Power Noise-Shaping SAR ADC with Improved Integrator and Hybrid DAC Mismatch Mitigation Technique

A 13-ENOB Second-Order Noise-Shaping SAR ADC Realizing Optimized NTF Zeros Using the Error-Feedback Structure

A 16.5-μW 73.7-dB-SNDR Second-Order Fully Passive Noise-Shaping SAR ADC With a Hybrid Switching Procedure

A 73db SNDR 20ms/s 1.28mw SAR-TDC Using Hybrid Two-Step Quantization.

A 0.0045 Mm2 31.5uw 312.5Khz-Bw 2Nd-Order Noise-shaping SAR ADC with a Dynamic-BulkSwitching Single-Transistor Amplifier

An 871 Nw 96.2 Db SNDR Pipelined Second-Order Noise-Shaping SAR ADC Employing Charge-Efficient CLS-Assisted Residue Amplifier

A 68 uW 31 kS/s Fully-Capacitive Noise-Shaping SAR ADC with 102 dB SNDR

A 13.5-ENOB, 107-μW Noise-Shaping SAR ADC With PVT-Robust Closed-Loop Dynamic Amplifier

A 10.5-B ENOB 645 Nw 100ks/s SAR ADC with Statistical Estimation Based Noise Reduction

A 91 Db SNDR Calibration-Free Fully-Passive Noise-Shaping SAR ADC with Mismatch Error Shaping

A 13-Enob 2nd-Order Noise-Shaping Sar Adc Realizing Optimized Ntf Zeros Using An Error-Feedback Structure

A 10 MS/s 10 bit SAR A/D Converter in RF System

28.1 A 0.46mW 5MHz-BW 79.7dB-SNDR noise-shaping SAR ADC with dynamic-amplifier-based FIR-IIR filter