Abstract:The generation of wear particles is now considered one of the most important failures in total arthroplasty. It is especially needed to study damage process of the particles at slight movement and lower load for long-term service of implanted materials. The wear and abrasion behavior of particles on Ti–6Al–4V coated with diamond-like carbon (DLC) were appropriately simulated in the present paper by fretting wear and nano-scratch test. The coatings with a thickness of 2.5 μm were deposited with an r.f.-plasma enhanced chemical vapor deposition method. The analytic techniques employed to assess DLC coatings characterization include SEM, AFM, Raman and IR spectroscopy. Assessment of hardness, elastic modulus, abrasion and adhesion of the coatings were performed using a Nano Indenter XP system with attachments of continuous stiffness measurements (CSM) and lateral force measurements (LFM). Tribological properties of the coatings were evaluated by a fretting wear test. It was concluded that the DLC coatings had a smooth surface morphology with a rms of 6.8 nm and possessed good adhesion to the substrate, they recovered fully elastic at lower load (60 mN) and were ploughed and delaminated only partially at higher load (400 mN). Nevertheless, there was wear debris concurrently generated during the nano-scratch and fretting test, which was more evident at high loads for a definite coatings, indicating an essential necessity of the work to improve the wear resistant of the coatings to avoid the generation of wear debris. The friction coefficient of DLC coatings against corundum obtained by fretting test decreased with the increase of relative humidity, it was below 0.1 in an aqueous condition, this may be beneficial to their biomedical applications in body fluids.

Corrosion and Scratch Resistance of DLC Coatings Applied on Chromium Molybdenum Steel

Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

Comprehensive structural, nanomechanical and tribological evaluation of silver doped DLC thin film coating with chromium interlayer (Ag-DLC/Cr) for biomedical application

Nano-scratch and Fretting Wear Study of DLC Coatings for Biomedical Application

Influence of the Metallic Sublayer on Corrosion Resistance in Hanks' Solution of 316L Stainless Steel Coated with Diamond-like Carbon

Enhanced tribological and corrosion properties of DLC/CrN multilayer films deposited by HPPMS

Exploring long-run reciprocating Wear of diamond-like carbon coatings: microstructural, morphological and tribological evolution

Synergistic Effect of Cr-Doped DLC Coatings and Lubricant Additives

The development of B/Cr co-doped DLC coating by FCVA deposition system and its tribological properties at 300 °C

Excellent Adhered Thick Diamond-Like Carbon Coatings by Optimizing Hetero-Interfaces with Sequential Highly Energetic Cr and C Ion Treatment

Corrosion Protection of Ultra-Thin Diamond-Like Carbon Films on Cuprum

Analysis on the Interfacial Mechanics of Microscratching Test for DLC-G95Cr18 Film-Substrate System

Corrosion behavior and passive stability of multilayer DLC-Si coatings

Scratch Behavior of DLC Film Deposited by Plasma Based Ion Implantation & Deposition

Characterisation of Ultra-Thin DLC Coatings by SEM/EDX, AFM and Electrochemical Techniques

Effects of sp3 bond ratio and modulation ratios on nanotribology behaviors of diamond-like carbon coatings investigated using atomistic nanoscratching simulations

Structure and Anticorrosion, Friction, and Wear Characteristics of Pure Diamond-Like Carbon (DLC), Cr-DLC, and Cr-H-DLC Films on AZ91D Mg Alloy

Mechanical and Corrosion Study of Diamond-Like Carbon Coating on Niti Alloys

Tribological study of lubricious DLC biocompatible coatings

Tribological Behaviors of Diamond-Like Carbon Coatings on Plasma Nitrided Steel Using Three BN-containing Lubricants

Structure related corrosion behavior of DLC films in high Cl − environment