Abstract:As an important joint material, tantalum (Ta) needs to be studied intensively in terms of wear and corrosion resistance. Two films of Ta/Ti/DLC (diamond-like carbon) (referred to as TD film) and Ta/Ti/TiN/Ti/DLC (referred to as TTTD film) were prepared by magnetron sputtering technology, and their electrochemical corrosion performance in lactic acid and sodium bicarbonate solutions was also investigated. The morphology observation, electrochemical corrosion experiment, and static contact angle measurement were carried out using a scanning electron microscope, electrochemical workstation, and a contact angle meter. This paper mainly discusses and analyzes the corrosion influencing factors and corrosion mechanisms of these two films under two different environments. The 20-day immersion experiments show that the TD film in both solutions results in severe surface corrosion due to its loose structure and many internal defects. In contrast, the surface of the TTTD film with a dense structure, a multilayer structure, and a thicker thickness is not corroded under the same conditions. The electrochemical corrosion experiments show that the corrosion resistance of the TD film is worse than that of the Ta substrate, while the TTTD film has the strongest corrosion resistance, improving the corrosion resistance of the Ta substrate. Although the TD film had a higher sp3 content than the TTTD film, it does not provide protection to the Ta substrate due to increased structural defects in the TD film. The results of the contact angle show that the contact angle of the TTTD film is smaller than that of the TD film in both solutions. However, the TTTD film has the lowest roughness and the densest structure, and thus the TTTD film is more resistant to corrosion. It is finally concluded that the surface morphology and internal structure of the films are the main factors affecting corrosion resistance. This provides an important reference for the application of DLC film in weak alkaline and weak acid environments.

Corrosion Protection of Ultra-Thin Diamond-Like Carbon Films on Cuprum

The Protective Properties of Ultra-Thin Diamond Like Carbon Films for High Density Magnetic Storage Devices

Tribological Properties of Diamond-Like Carbon Films Deposited by Vacuum Arc

Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

Wear-resistance of Diamond-like Carbon Thin Films Deposited on the Metal Seal Ring Surface by Plasma Gun at an Atmospheric Pressure

Characterisation of Ultra-Thin DLC Coatings by SEM/EDX, AFM and Electrochemical Techniques

Corrosion Properties of DLC Film in Weak Acid and Alkali Solutions

Enhanced tribological and corrosion properties of DLC/CrN multilayer films deposited by HPPMS

Mechanical and Tribological Properties of Diamond-Like Carbon Films Deposited by Electron Cyclotron Resonance Microwave Plasma Chemical Vapor Deposition

A Novel Diamond-Like Carbon Film

Excellent Adhered Thick Diamond-Like Carbon Coatings by Optimizing Hetero-Interfaces with Sequential Highly Energetic Cr and C Ion Treatment

Structure and Anticorrosion, Friction, and Wear Characteristics of Pure Diamond-Like Carbon (DLC), Cr-DLC, and Cr-H-DLC Films on AZ91D Mg Alloy

Diamond-Like Carbon Thin Films Deposited On Ti6al4v Alloy Surface By Plasma Gun At Atmospheric Pressure

Electrodeposition, microstructure, friction and electrochemical behavior of diamond-like carbon (DLC) films with Ni/Cu interlayer

Structure related corrosion behavior of DLC films in high Cl − environment

Structural Characters and Tribological Properties of Diamondlike Carbon Films

Microstructure, wear and corrosion behavior of nano-CeO2 doped diamond-like carbon (DLC) composite films

A study of the wear mechanism of diamond-like carbon films

Fatigue and Frictional Behavior of Diamond-like Carbon Films Deposited by Filtered Cathodic Vacuum Arc Technique

Anti-sand erosion and tribological performance of thick DLC coatings deposited by the filtered cathodic vacuum arc

Magnetron Sputtering Preparation of Diamond-Like Carbon Film Adhesion Characteristics Research