Abstract:Phase-transformations and microstructural evolution during and after inter-critical annealing of a low-alloy, dual-phase steel are studied utilizing dilatometric measurements, and microstructural characterization methods, including scanning electron microscopy, synchrotron X-ray diffraction, and atom-probe tomography. Dilatometric measurements reveal that the sample contains ~72% austenite, after annealing for 5-min at 871 oC, which agrees with the water-quenched microstructure, and ~90% after further annealing to 1 h, which agrees with thermodynamic predictions. A continuous-cooling transformation (CCT) diagram is constructed, within the cooling-rate range between 1 oC/s and 70 oC/s. The incubation time for the ferrite-transformation is <1 s, after inter-critical annealing, and the secondary-phases are mainly pearlite for cooling-rates of <5 oC/s, and martensite for cooling-rates >10 oC/s, which is confirmed utilizing scanning electron-microscope observations. The microhardness increases as the cooling rate increases, and an abrupt slope-change is explained by the major secondary-phase changing from martensite to pearlite between 5 oC/s and 10 oC/s. Atom-probe tomography demonstrates the coexistence of martensite and pearlite as secondary-phases for 30 oC/s and a switch in austenite-ferrite transformation mechanisms from para-equilibrium (70 oC/s) to partitioning local-equilibrium (30 oC/s). A microstructural map is constructed to reveal the austenite decomposition products in the cooling-rate range between 1 oC/s and 70 oC/s. Based on composition measurements of the matrix, utilizing APT, the effects of cooling-rates on solid-solution-strengthening are estimated, and the results demonstrate that solid-solution strengthening, especially carbon-redistribution, accounts for the majority of the strength variations due to different cooling-rates. (239 words)

Investigation of Massive Ferrite in an Interstitial-Free Steel

Intragranular Ferrite Formation Mechanism and Mechanical Properties of Non-quenched-and-tempered Medium Carbon Steels

New Insights into Intragranular Ferrite in a Low-Carbon Low-Alloy Steel

Kinetics and Mechanisms of Intragranular Ferrite Nucleation on Non-Metallic Inclusions in Low Carbon Steels

In Situ Observation of Acicular Ferrite Formation and Grain Refinement in Simulated Heat Affected Zone of High Strength Low Alloy Steel

Diffusional and displacive transformations in interstitial-free steel within the scope of a critical assessment of the mechanical property

In-situ Investigation of Phase Transformation Behaviors of 300M Steel in Continuous Cooling Process

Formation of needle like proeutectiod ferrite and its influence on medium carbon steel wire properties

In-Situ Observations of Acicular Ferrite Growth Behavior in the Simulated Coarse-Grained Heat-Affected Zone of High-Strength Low-Alloy Steels

In situ observation of the austenite to ferrite transformation in low-carbon steels from different initial phases at defined cooling rates

Atom-probe tomographic and dilatometric studies of phase-transformations after inter-critical annealing of a low-carbon dual-phase steel

Ultrafine Grain Ferrite Transformed from Fine Austenite Grains Produced by Dynamic Reversal Transformation

Influence of Low-temperature Deformation of Ferrite and Carbide Dual Phase Microsturcture on the Microstructure of Low Carbon Steel

Investigation of Annealed Ultra-fine Ferrite Microstructures in a Plain Low Carbon Steel Q235

Effects of acicular ferrites on crystallography and incomplete transformation of low-carbon low-alloy steel

Study of Ferrite During Refinement of Prior Austenite Grains in Microalloyed Steel Continuous Casting

Dynamic recrystallization of ferrite in a low-carbon steel

Investigating Microstructural Properties of Ferrite/bainite Dual-Phase Steel Through Simple Process Control

Study on Ferrite Transformation Obtained by Dynamic Transformation of Undercooled Austenite of Low Carbon Steel

Ferrite Formation Dynamics and Microstructure Due to Inclusion Engineering in Low-Alloy Steels by Ti2O3 and TiN Addition

The austenite to polygonal ferrite transformation in low-alloy steel: multi-phase-field simulation