Abstract:In spite of the advantages of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) cathode materials such as high energy density and high capacity, their capacity decay during cycling is still a significant problem, which are mainly due to the internal structural collapse and the surge in interfacial impedance caused by interfacial side reactions. To address these issues, wet chemical methods and annealing treatments were used to create LiV 2 O 4 -coated and V 4+ -doped NCM811 cathode materials. The LiV 2 O 4 coating layer and the doped V 4+ had little effect on the crystal structure of the NCM811, according to X-ray powder diffraction and Rietveld refinement studies. Scanning electron microscopy, energy dispersive spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy data all showed that the LiV 2 O 4 layer was successfully coated on the surface of the spherical particles and some of the V 4+ was successfully introduced into the bulk phase. Thanks to the ion-conducting layer, LiV 2 O 4 , the interfacial impedance was reduced while the Li + diffusion rate was accelerated, and the V 4+ doped into the bulk phase stabilizes the internal structure, significantly increasing the cycling stability and the rate performance of NCM811. In particular, when the coating amount was 0.6 wt%, the initial discharge specific capacity reached 203.5 mAh/g at 2.8–4.3 V at 0.1 C, and the retention rate was 87.6% after 100 cycles, which was 12.1% higher compared to 75.5% of the original sample. And when the rate was raised to 5 C, the original sample's capacity plummeted to only about 100 mAh/g, but the sample with 0.6 wt% of coating was still 140.9 mAh/g. Experiments confirmed that this LiV 2 O 4 coating modification with synergistic V 4+ doping provided an innovative technique for boosting the electrochemical performance of Ni-rich ternary cathode materials.

Surface Modification on Enhancing the High-Voltage Performance of LiNi0.8Co0.1Mn0.1O2 Cathode Materials by Electrochemically Active LiVPO4F Hybrid

Enhancing high-voltage performances of nickel-based cathode material via aluminum and progressive concentration gradient modification

Improving electrochemical performance of LiMn<sub>0.5</sub>Fe<sub>0.5</sub>PO<sub>4</sub> cathode by hybrid coating of Li<sub>3</sub>VO<sub>4</sub> and carbon

Improved Cycle Stability of High-Capacity Ni-rich LiNi0.8Mn0.1Co0.1O2 at High Cut-off Voltage by Li2SiO3 Coating

Enhanced electrochemical performance of LiV2O4-coated and V4+-doped LiNi0.8Co0.1Mn0.1O2 cathode for lithium-ion batteries

Improving the Cycling Stability of Li-Rich Mn-Based Cathodes through Surface Modification of VOPO 4

Understanding the Effects of Surface Modification on Improving the High-Voltage Performance of Ni-rich Cathode Materials

Improving the Cycling Stability of Li-Rich Mn-Based Cathodes Through Surface Modification of VOPO4

Improving the Electrochemical Performance of LiNi1/3Co1/3Mn1/3O2 Cathode Material by LiF Modification

Improved electrochemical performance of layered Li1.2Ni0.13Co0.13Mn0.54O2 cathode material via VPO5 coating

Surface Modification Driven Initial Coulombic Efficiency and Rate Performance Enhancement of Li1.2Mn0.54Ni0.13Co0.13O2 Cathode

Enhanced Electrochemical Performance of LiNi1/3Co1/3Mn1/3O2 at a High Cut-Off Voltage of 4.6 V by Li1.3Al0.3Ti1.7(PO4)3 Coating

Improvement of electrochemical performance and structural stability of LiNi0.83Co0.12Mn0.05O2 at high-voltage by La and Ti modification

Lithium-conductive LiNbO3 Coated High-Voltage LiNi0.5Co0.2Mn0.3O2 Cathode with Enhanced Rate and Cyclability

Improving Stability of High Voltage LiCoO2 by Synergetic Surface Modification Via in Situ Surface Conversion

Improved High Rate Capability of Li[Li0.2Mn0.534Co0.133Ni0.133]O2 Cathode Material by Surface Modification with Co3O4

Uncovering the Role of Nb Modification in Improving the Structure Stability and Electrochemical Performance of LiNi 0.6 Co 0.2 Mn 0.2 O 2 Cathode Charged at Higher Voltage of 4.5 V

Enhancing the Electrochemical Performance of High Voltage LiNi0.5Mn1.5O4 Cathode Materials by Surface Modification with Li1.3Al0.3Ti1.7(PO4)3/C

A Uniform and High-Voltage Stable LiTMPO4 Coating Layer Enabled High Performance LiNi0.8Co0.15Mn0.05O2 Towards Boosting Lithium Storage.

In-situ Formation of Hybrid Li3PO4-AlPO4-Al(PO3)3 Coating Layer on LiNi0.8Co0.1Mn0.1O2 Cathode with Enhanced Electrochemical Properties for Lithium-Ion Battery

Multifunctional Integration of Double-Shell Hybrid Nanostructure for Alleviating Surface Degradation of LiNi0.8Co0.1Mn0.1O2 Cathode for Advanced Lithium-Ion Batteries at High Cut-Off Voltage.