Abstract:In spite of the advantages of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM811) cathode materials such as high energy density and high capacity, their capacity decay during cycling is still a significant problem, which are mainly due to the internal structural collapse and the surge in interfacial impedance caused by interfacial side reactions. To address these issues, wet chemical methods and annealing treatments were used to create LiV 2 O 4 -coated and V 4+ -doped NCM811 cathode materials. The LiV 2 O 4 coating layer and the doped V 4+ had little effect on the crystal structure of the NCM811, according to X-ray powder diffraction and Rietveld refinement studies. Scanning electron microscopy, energy dispersive spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy data all showed that the LiV 2 O 4 layer was successfully coated on the surface of the spherical particles and some of the V 4+ was successfully introduced into the bulk phase. Thanks to the ion-conducting layer, LiV 2 O 4 , the interfacial impedance was reduced while the Li + diffusion rate was accelerated, and the V 4+ doped into the bulk phase stabilizes the internal structure, significantly increasing the cycling stability and the rate performance of NCM811. In particular, when the coating amount was 0.6 wt%, the initial discharge specific capacity reached 203.5 mAh/g at 2.8–4.3 V at 0.1 C, and the retention rate was 87.6% after 100 cycles, which was 12.1% higher compared to 75.5% of the original sample. And when the rate was raised to 5 C, the original sample's capacity plummeted to only about 100 mAh/g, but the sample with 0.6 wt% of coating was still 140.9 mAh/g. Experiments confirmed that this LiV 2 O 4 coating modification with synergistic V 4+ doping provided an innovative technique for boosting the electrochemical performance of Ni-rich ternary cathode materials.

Improved electrochemical performance of layered Li1.2Ni0.13Co0.13Mn0.54O2 cathode material via VPO5 coating

Enhanced electrochemical performance of LiV2O4-coated and V4+-doped LiNi0.8Co0.1Mn0.1O2 cathode for lithium-ion batteries

Improvement of Electrochemical Properties of LiNi1/3Co1/3Mn1/3O2 by Coating with V2O5 Layer

Li3V2(PO4)3-coated Li1.17Ni0.2Co0.05Mn0.58O2 As the Cathode Materials with High Rate Capability for Lithium Ion Batteries

Improving the Cycling Stability of Li-Rich Mn-Based Cathodes through Surface Modification of VOPO 4

Improving the Cycling Stability of Li-Rich Mn-Based Cathodes Through Surface Modification of VOPO4

Suppressed Voltage Decay and Improved Electrochemical Performance by Coating LiAl5O8 on the Surface of Li1.2Mn0.54Ni0.13Co0.13O2

Enhanced Electrochemical Performance of Li1.2mn0.54ni0.13co0.13o2 Cathode with an Ionic Conductive Livo3 Coating Layer

Integrated co-modification of PO43− polyanion doping and Li2TiO3 coating for Ni-rich layered LiNi0.6Co0.2Mn0.2O2 cathode material of Lithium-Ion batteries

Improved Electrochemical Performances of Li- and Mn-Rich Layered Oxides 0.4li4/3mn2/3o2·0.6lini1/3co1/3mn1/3o2 Cathode Material by Co3O4 Coating

Boosting the performance of LiNi0.90Co0.06Mn0.04O2 electrode by uniform Li3PO4 coating via atomic layer deposition

Improved Electrochemical Performance and Thermal Stability of Li-Excess Li1.18co0.15ni0.15mn0.52o2 Cathode Material by Li3po4 Surface Coating

Improving the Electrochemical Performance of Li-rich Li1.2Ni0.2Mn0.6O2 by Using Ni-Mn Oxide Surface Modification

Amorphous Li2ZrO3 nanoparticles coating Li[Li0·17Mn0·58Ni0.25]O2 cathode material for enhanced rate and cyclic performance in lithium ion storage

Enhanced Stability of Vanadium-Doped Li1.2Ni0.16Co0.08Mn0.56O2 Cathode Materials for Superior Li-ion Batteries

Effect of carbon coating on electrochemical performance of Li 1.048 Mn 0.381 Ni 0.286 Co 0.286 O 2 cathode material for lithium-ion batteries

Improving electrochemical performance of LiMn<sub>0.5</sub>Fe<sub>0.5</sub>PO<sub>4</sub> cathode by hybrid coating of Li<sub>3</sub>VO<sub>4</sub> and carbon

Significant Enhancement of the Capacity and Cycling Stability of Lithium-Rich Manganese-Based Layered Cathode Materials via Molybdenum Surface Modification

Enhanced electrochemical performance of cobalt oxide layers coated LiNi0.8Co0.1Mn0.1O2 by polyvinylpyrrolidone-assisted method cathode for Li-ion batteries

In-situ formation of Li0.5Mn0.5O coating layer through defect controlling for high performance Li-rich manganese-based cathode material

Enhanced Electrochemical Performance of Li[Li0.2ni0.2mn0.6]O-2 Modified by Manganese Oxide Coating for Lithium-Ion Batteries