Abstract:3D C-f/SiC-Al composites were achieved through the pressure infiltration of liquid Al-Si alloy into porous 3D C-f/SiC preform, which was produced by different cycles of precursor infiltration and pyrolysis. The effect of silicon carbide volume fraction on the microstructure, anisotropic mechanical response, and thermophysical characteristics of the 3D C-f/SiC-Al composites was investigated. The results demonstrated that the initial microstructure of 3D C-f/SiC can be retained, and the obtained C-f/SiC-Al composites presented remarkable anisotropy characteristics. As the silicon carbide ceramics content increased from 12.5 vol% to 41.8 vol%, the thermal conductivity and thermal expansion coefficient of 3D C-f/SiC-Al composites decreased, whereas the bending strength initially increased and then decreased in the Z-direction. The bending strength perpendicular (Z) to the carbon cloth layer of 3D C-f/SiC-Al composites was higher than that of parallel (X-Y) to the carbon cloth layer. However, a significant anisotropy in the thermal conductivity values was the opposite. The 3D C-f/SiC-Al composite with low ceramic content (17 vol%) had a higher thermal conductivity in the X-Y direction (64 W m(-1) K-1) than in the Z-direction (34 W m(-1) K-1). The thermal expansion coefficient of all the 3D C-f/SiC-Al composites along the X-Y direction also decreased initially and then increased in the range of 100-450 degrees C, which presents low expansion characteristics.

Effects of Aligned Carbon Nanotube Microcolumns on Mechanical and Thermal Properties of C/SiC Composites Prepared by LA-CVI Methods

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

Effects of SiC Content on the Mechanical and Thermophysical Properties of 3D Cf/SiC–Al Composites

Effect of mass transfer channels on flexural strength of C/SiC composites fabricated by femtosecond laser assisted CVI method with optimized laser power

Effect of CNT impregnation on the mechanical and thermal properties of C/C-SiC composites

Effects of Carbon Fiber Architecture on the Microstructure and Mechanical Property of C/C-SiC Composites

Thermal Properties of Aligned Carbon Nanotube/Carbon Nanocomposites

Effects of Carbon Nanotube Content on Morphology of SiCp(CNT) Hybrid Reinforcement and Tensile Mechanical Properties of SiCp(CNT)/Al Composites

Exploring the size effects of Al4C3 on the mechanical properties and thermal behaviors of Al-based composites reinforced by SiC and carbon nanotubes

Effect of Carbon Nanotube (CNT) Content on the Properties of In-Situ Synthesis CNT Reinforced Al Composites

In-situ synthesis and microstructural evolution of a SiC reinforced Al-50Si composite exhibiting exceptional thermal properties

3C-SiC Nanowires In-Situ Modified Carbon/Carbon Composites and Their Effect on Mechanical and Thermal Properties

Effect of initial density on thermal conductivity of new micro‐pipeline heat conduction C/SiC composites

Investigation on the Microstructure and Mechanical Properties of CNTs-AlSi10Mg Composites Fabricated by Selective Laser Melting

Preparation, microstructure and properties of three-dimensional carbon/carbon composites withhigh thermal conductivity

Enhanced thermal and mechanical properties of optimized S i C f / S i C composites with in-situ CNTs on PyC interface

Investigation into the influence of CNTs configuration on the thermal expansion coefficient of CNT/Al composites

Effects of La and Ce on Microstructure and Properties of SiC/Al Composites

Thermal management applied laminar composites with SiC nanowires enhanced interface bonding strength and thermal conductivity

Effect of Carbon Nanotube Orientation on Mechanical Properties and Thermal Expansion Coefficient of Carbon Nanotube-Reinforced Aluminum Matrix Composites

Microstructures, thermal and mechanical properties of Al–Si-CNT composites for thermal management applications