Abstract:The objective of this work is a dilatometric study of Al + 0.1% of multiwall carbon nanotubes nanocomposite material (NCM) in three directions: X - parallel to the rolling direction; Y - perpendicular to the rolling direction and (Z) perpendicular to the ribbon plane. NCM specimens were made in the form of a 0.1-mm-thick ribbon. The temperature range used for measurements was 20°C to 600°C. The obtained results show that presence of nanotubes affects the thermal expansion coefficient (TEC) measured in different directions. αx(T) and αy(T) - TEC plots as a function of temperature along X and Y directions, respectively - have substantially the same shape and overlap in the area of 400°C. The expansion along X-axis becomes greater than along Y-axis below this temperature value. It is clear that the coefficient αz(T) is lower than αx(T) and αy(T) over the entire temperature range. The expansion along Z-axis is smaller compared to that along X- and Y-axes. This behaviour suggests that there is a strong interatomic interaction along this direction (Z). αz(T) becomes monotonous and constant and is equal to 8 × 10(-6)°C(-1) at temperatures above 300°C. Such order of magnitude had not been obtained in earlier studies of aluminium alloys. The obtained TEC shows high anisotropy, which grows with the increase of temperature. The heat flow (differential scanning calorimetry, (DSC)) of Al + 0.1% carbon nanotubes (CNT) NCM is more intense compared to that of pure aluminium produced in similar conditions. The two representative curves have similar shape and are almost entirely overlapped. The thermogravimetry results confirm those of DSC. The Raman spectrum of this nanomaterial shows that intensity of G and D bonds is significantly increased compared to that of the pure material. The infrared diagram also confirms that in this case the mentioned bonds are more intensive NCM. The tensile strength measurements (σB) of the studied NCM also demonstrate that its value increases from 140 ± 10 MPa for Al without nanotubes to 200 ± 10 MPa for NCM.

Effect of Carbon Nanotube Orientation on Mechanical Properties and Thermal Expansion Coefficient of Carbon Nanotube-Reinforced Aluminum Matrix Composites

Carbon-nanotube-templated Carbon Nanofibers with Improved Mechanical Performance

Investigation into the influence of CNTs configuration on the thermal expansion coefficient of CNT/Al composites

Mechanical properties of CNT-reinforced Ni3Al composites: the role of chirality, temperature, and volume fraction

Effect of carbon nanotube hybrid on the microstructure and properties of AlN skeleton-reinforced highly oriented graphite flake composites

Effect of carbon nanotubes on mechanical properties of aluminum matrix composites: A review

Carbon nanotubes/aluminum interface structure and its effects on the strength and electrical conductivity of aluminum

Effect of carbon nanotube content on the microstructure and mechanical properties of CNTs/TiAl alloys

Study on the Mechanism of CNTs Regulating the Microstructures and Properties of Al–Cu–Mg Alloy

Thermal analysis of Al + 0.1% CNT ribbon

Effects of Anisotropy, Aspect Ratio, and Nonstraightness of Carbon Nanotubes on Thermal Conductivity of Carbon Nanotube Composites

Effect of carbon nanotubes grown temperature on the fracture behavior of carbon fiber reinforced magnesium matrix composites: Interlaminar shear strength and tensile strength

Compressive behavior of CNT-reinforced aluminum matrix composites under various strain rates and temperatures

The Effects of Morphology and Temperature on the Tensile Characteristics of Carbon Nitride Nanothreads.

Effect of Carbon Nanotubes as Reinforcement on the Mechanical Properties of Aluminum-Copper-Magnesium Alloy

Effect of thermomechanical treatment and length-scales on spatial distribution of CNTs in Al matrix

Atomic insights into the tensile behavior of carbon nanotube with different geometrical characteristics embedded in nickel matrix

Fabrication and Tribological Properties of Carbon Nanotubes-Aluminum Composites

Carbon Nanotubes Grown on Graphite Films as Effective Interface Enhancement for an Aluminum Matrix Laminated Composite in Thermal Management Applications

Effect of powder microstructure on the thermal and mechanical properties of hot extruded Al-CNT composite

Enhancement of thermal–mechanical performances via a selective CNTs configuration in laminated CNTs/AZ31B composite