Abstract:A weighting‐factor‐free finite control set predictive torque control (FCS‐PTC) has been developed for induction motor drives by incorporating a hysteresis controller to eliminate stator flux error from the cost function. The tuning of the weighting factor coefficient in FCS‐PTC is critical for improved drive performance. The proposed method regulates the flux by incorporating a separate two level hysteresis controller and torque by the conventional cost function based PTC. The cost function uses torque error only and employs a reduced number of voltage vectors. The reduction of voltage vectors is obtained through the flux hysteresis output and sector determination. The obtained results show comparable dynamic performance of the drive with 43% lower computational burden as compared to conventional PTC. Along with computational benefits, proposed work also demonstrates improved total harmonic distortion (THD) at low speed regions due to the absence of weighting factor in cost function. This work proposes a weighting‐factor‐free finite control set predictive torque control (FCS‐PTC) for induction motor drives by incorporating a hysteresis controller to eliminate stator flux error from the cost function. The tuning of the weighting factor coefficient in FCS‐PTC is critical for improved drive performance. Conventionally, the tuning is based on an intuitive understanding of the dynamical system and empirical methods, which may not yield optimal results. The proposed method regulates the flux by incorporating a separate two‐level hysteresis controller and torque by the conventional cost function‐based PTC. The cost function uses torque error only and employs a reduced number of voltage vectors. The reduction of voltage vectors is obtained through the flux hysteresis output and sector determination. The proposed work is implemented experimentally on the dSpace DS1104 controller board for a two‐level three, three‐phase voltage source inverter‐fed induction motor drive. The experimental results validate the effectiveness of the proposed work under different drive tests compared to conventional PTC and direct torque control (DTC). The obtained results show comparable dynamic performance of the drive with 43% lower computational burden than conventional PTC. Along with computational benefit, the proposed work demonstrates improved total harmonic distortion (THD) at low‐speed regions due to the absence of a weighting factor in the cost function.

A Graphical Performance Tool for Design and Comparative Assessment of Predictive Torque Control Methods in Motor Drive Applications

Comparative Study of Flux-Weakening Control Methods for Pmsm Drive over Wide Speed Range

Comparative Study of Parameter Mismatch on Different Model Predictive Controls for PMSM Drives

Predictive Torque Control for PMSM Based on Weighting Factor Elimination and Fast Voltage Vector Selection

Simple predictive torque control of an open‐end winding interior permanent magnet synchronous motor drive without weighting factor for electric vehicle applications

A Reduced Voltage Vector Strategy-Based PTC of OEW-PMSM Drives

Hysteresis based predictive torque control without weighting factors for induction motor drives

A look-up table-based model predictive torque control of IPMSM drives with duty cycle optimization

Model predictive flux control for permanent magnet synchronous motor

Predictive power control of induction motor drives with improved efficiency

An Explicit MPTC Method for Improving Dynamic Performance of SPM

Fault-Tolerant Predictive Torque Control Design for Induction Motor Drives Based on Discrete Space Vector Modulation

Maximum Torque Per Ampere Control of IPMSM Based on Online Parameter Identification Considering Cross-coupling and Saturation Effects

A novel weighting factor determined method of model predictive torque control for permanent magnet synchronous motor

Model Predictive Torque Control of Surface Mounted Permanent Magnet Synchronous Motor Drives with Voltage Cost Functions

Experimental Evaluation of VIKOR-Based Cost Function Optimization of Finite Control Set-Predictive Torque Control for Permanent Magnet Synchronous Motor Drive

Neural-Network-Based Predictive Control for PMSM Drives

Torque-Performance Improvement for Direct Torque-Controlled PMSM Drives Based on Duty-Ratio Regulation

Adaptive Sliding-Mode-Based Speed Control in Finite Control Set Model Predictive Torque Control for Induction Motors

Dual-Vector-Based Predictive Torque Control for Fault-Tolerant Inverter-Fed Induction Motor Drives With Adaptive Switching Instant

Model Predictive Thrust Control for Linear Induction Machine: A Fuzzy Optimization Approach