Abstract:Stable slurries for Si3N4-bonded SiC refractories for direct ink writing (DIW) were successfully prepared from a mixture of non-spherical silicon carbide (SiC) and silicon (Si) powders with an average particle size of D50 = 41.98 μm. The rheological properties and printability of slurries prepared using polyvinyl alcohol (PVA; 4–16 wt %) or hydroxypropyl methylcellulose (HPMC, 0.5–2 wt.%) were investigated with the effect of sintering temperature on the mechanical performance, phase, and microstructure of Si3N4-bonded SiC refractory products. The results indicated that slurries prepared with the HPMC solution showed better printability than those prepared with the PVA solution because colloidal films formed by HPMC in slurries play a role in encasing particles, preventing solid−liquid separation and contributing to plasticity and lubrication, which guarantees the smooth extrusion and homogeneity of slurries. The successful printing of SiC–Si slurries is not only related to proper viscosity, yield value, and shear thinning characteristics but it is also crucial for maintaining the homogeneity of slurries under extrusion pressure. Optimal SiC–Si slurries containing 52 vol % SiC–Si and 1.5 wt% HPMC exhibited proper viscosity, shear thinning, and homogeneity characteristics during printing. The obtained specimens achieved the best printing performance with height and section retention rates of 98.7% and 97.6%, respectively. When sintered at 1450 °C, Si3N4 fibres grow further and reach a diameter of 342.5 nm, the nitriding rate is 92.43%, the fibres tend to form a full network structure, and the mechanical properties of Si3N4-bonded SiC products are the best.

3D SiC Containing Uniformly Dispersed, Aligned SiC Whiskers: Printability, Microstructure and Mechanical Properties

3D-SiC decorated with SiC whiskers: Chemical vapor infiltration on the porous 3D-SiC lattices derived from polycarbosilane-based suspensions

In-situ formed SiC whisker strengthening of silicon carbide reticulated porous ceramics based on 3D printed lattices template

Microstructure control of SiCw/SiC composites based on SLS technology

Microstructures, Mechanical Properties and Electromagnetic Wave Absorption Performance of Porous SiC Ceramics by Direct Foaming Combined with Direct-Ink-Writing-Based 3D Printing

Microstructure, thermal, and mechanical properties of hierarchical porous silicon carbide made by direct ink writing

Silicon carbide whiskers reinforced SiOC ceramics through digital light processing 3D printing technology

Thermally assisted extrusion-based 3D printing of continuous carbon fiber-reinforced SiC composites

Direct Ink Writing of Chopped Carbon Fibers Reinforced Polymer-derived SiC Composites with Low shrinkage and High Strength

Binder jetting additive manufacturing of hierarchical structural SiC w /SiC composites

Controllable reduction of absorbance and two-step reaction for 3D-printed SiC ceramics with micron-level periodic structure

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Geometrically Complex Silicon Carbide Structures Fabricated by Robocasting

Additive manufacturing of high mechanical strength continuous Cf/SiC composites using a 3D extrusion technique and polycarbosilane‐coated carbon fibers

3D printing Si3N4-bonded SiC refractories fabricated using colloidal films-containing slurries based on non-spherical SiC and Si powders

Building SiC-based composites from polycarbosilane-derived 3D-SiC scaffolds via polymer impregnation and pyrolysis (PIP)

Curing behaviors and mechanical properties of SiC-whisker-reinforced alumina ceramics fabricated with digital light processing

Mechanical and tribological properties of SiC whiskers reinforced SiC composites via oscillatory pressure sintering

Mechanical and Tribological Properties of SiC Whisker‐reinforced SiC Composites Via Oscillatory Pressure Sintering

Improved Sinterability of SiC(w)/Si3N4 Composites by Whisker-Oriented Alignment

Additive manufacturing of complexly shaped SiC with high density via extrusion-based technique – Effects of slurry thixotropic behavior and 3D printing parameters