Abstract:The geometric parameters and stress conditions of fractures are the main factors that determine the strength and deformation characteristics of fractured rock masses, and the ultimate instability and failure of fractured rock masses are caused by the extension and penetration of the structural plane. In this study, a series of Φ50 × 100 mm standard cylinder specimens were prepared to simulate brittle rock masses. The uniaxial compressive strength and tensile strength of the specimens were 33 and 2.8 MPa, respectively. Non-persistent fractures with different inclination angles, connectivity rates, openings, spacings, groups, and roughness were prefabricated in the specimens, and the fractures were filled with plasticine. Furthermore, the crack propagation and failure mechanisms of filled fractured rock masses under uniaxial compression (the loading rate is 0.2 MPa/s) were analyzed by a 3D video image correlation system. Comparing the results of this research with those of previous researches, and combining with relevant theoretical analysis, the following conclusions are drawn: (1) the curve of the peak strength reduction coefficient k σ of the specimen with the fracture inclination angle α is roughly V-shaped, and being the smallest when the fracture inclination angle α is 45°; the reduction coefficient k is monotonically decreasing with the three groups of fracture geometric parameters of spacing b , connectivity rate μ , and opening d , and the peak strength reduction coefficient k σ of the specimen is typically smaller than the elastic modulus reduction coefficient k E . (2) The post-peak stress–strain curve of the specimen with filled fractures is relatively slow, and the plasticity is obviously enhanced. The geometric parameters of the fractures are important factors affecting the change of the mechanical properties of the specimen. The influence degree of different fractures geometric parameters on rock masses mechanical properties is as follows: fracture sets > spacing > connectivity rate > inclination angle > opening > roughness. (3) Due to the concentration of stress, cracks first initiate from the fracture tips, then propagate parallel to the loading direction, and ultimately coalesce between the fractures and the specimen surface. During the failure process of the specimens, four types of cracks were observed: tensile cracks, shear cracks, wing cracks, and reverse wing cracks, with wing cracks dominating crack propagation. (4) Compared with the specimens with unfilled fractures, the stress concentration at the filled fractures was reduced, and more microcracks with higher dispersion developed around the filled fracture.

Fracture Mechanical Properties and Fractal Analysis of Fracture Surfaces of Cortical Bone

Damage and Fracture Behavior of Cancellous Bone in the Femoral Head

Characterization of damage mechanisms in cortical bone: Quantification of fracture resistance, critical strains, and crack tortuosity

Differences in the mechanical behavior of cortical bone between compression and tension when subjected to progressive loading

A Mesoscopic Approach for the Size Effect on Fracture Energy of Concrete

A proposal for the combined analysis of bone quantity and quality of human cortical bone by quasi-brittle fracture mechanics

Fracture characterization of fractured rock bodies based on acoustic and optical characteristics

Approach to characterize rock fracture surface: Insight from its roughness and fractal dimension

Mechanical response and in-situ deformation mechanism of cortical bone materials under combined compression and torsion loads

Effects of Microstructure Characteristics of Cortical Bone on Its Microcrack Propagation

Prediction of mechanical properties of human rib cortical bone using fractal dimension

Experimental study on fracture characteristics of rock-like material with prefabricated cracks under compression shear

Experimental investigation on the fracture surface features of heat-treated red sandstone containing fissure under constant amplitude low cycle impact using 3D digital reconstruction

Immature porcine cortical bone mechanical properties and composition change with maturation and displacement rate

Characterizing Brittle Fracture by Modeling Crack Deflection Angles from the Microstructure

Anisotropic self-affine properties of experimental fracture surfaces

Constitutive relationships for osteonal microcracking in human cortical bone using statistical mechanics

Relationship between the microstructural energy release rate of cortical bone and age under compression condition

A Relationship between Fracture Toughness Kc and Energy Release Rate Gc According to Fracture Morphology Analysis

Fractal Characterization of the Fracture Surface of Untempered and Tempered Bainitic Modified 9Cr-1Mo Steel

Experimental Study on the Effects of Geometric Parameters of Filled Fractures on the Mechanical Properties and Crack Propagation Mechanisms of Rock Masses