Abstract:Cu/Al composites have the excellent properties of both Cu and Al, and have the properties of light weight and high conductivity, so they have been widely concerned. In this paper, 5-mm-thick Cu/Al composites prepared by the cast-rolling process are used as experimental materials. To reveal the strengthening and toughening mechanisms of the Cu/Al composites, the interfacial structure, micro-morphology, stress-strain condition, and GND distribution of Cu/Al composites before and after deformation were characterized utilizing TEM, TKD, and EBSD. The results show that the submicron intermetallic compounds Al 2 Cu and Al 4 Cu 9 are formed from the casting-rolling Cu/Al composites. After 15% tensile deformation, many gaps occurred in the interface layer, but at the gaps, there was no crack spreading to the Cu and Al layers. Meanwhile, the deformation in different directions occurs in the Cu grains near the interface, forming a dislocation wall, and the entanglement of the dislocation occurs in the Cu layer near the interface, which contributes to the improvement of tensile strength. The Al layer near the interface layer produces kink bands, which helps to improve the ductility of the composites. Besides, due to the action of the hard intermetallic compound layer, with the increase in tensile deformation, a large number of GND are gradually accumulated in the Cu and Al layers near the interface, resulting in remote back stress, which makes the softer Cu and Al layers obtain higher strength. At the same time, the back stress caused by GND will induce strain hardening, which helps to maintain ductility, so that Cu/Al composites have higher plastic deformation ability while improving mechanical properties.

Mechanical Properties and Tensile Fracture Mechanism Investigation of Al/Cu/Ti/Cu/Al Laminated Composites Fabricated by Rolling

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Microstructure and mechanical properties of Ti6Al4V based laminated composites at various rolling reductions

Texture characteristics and tensile deformation behavior of Cu/Al layered composites prepared by cast-rolling method

Microstructure and mechanical behavior of Ti/Cu/Ti laminated composites produced by corrugated and flat rolling

Fracture toughness, wear, and microstructure properties of aluminum/titanium/steel multi-laminated composites produced by cross-accumulative roll-bonding process

Comparison of Rolling and Transverse Direction Properties of Al/Ti Laminated Metal Composites Prepared by Cold Roll Bonding and Subsequent Annealing

Fabrication, microstructure, mechanical properties and wear behavior of Al/Cu-SiC w composite

Study of microstructure and mechanical properties of quasi-continuous network structured (Ti3AlC2-Al3Ti)/2024Al composites based on hot rolling

Microstructure and mechanical properties of high-temperature free-oxygen rolled Cu/1060Al bimetallic composite materials

Effect of Pre-Rolling on Microstructure and Fatigue Crack Propagation Resistance of a Third-Generation Al-Li Alloy

Effect of residual stresses on the mechanical properties of Ti-TiAl laminate composites fabricated by hot-pack rolling

Microstructure and Mechanical Properties of AA1050/AA6061 Laminated Composites Fabricated through Three-Cycle Accumulative Roll Bonding and Subsequent Cryorolling

Formation mechanism of dynamic multi-neutral points and cross shear zones in corrugated rolling of Cu/Al laminated composite

Fabrication of Al/Al-TiB 2 laminate composites via hot press sintering process: An insight into the mechanical properties and fracture behavior

Study on strengthening and toughening mechanisms of cu/Al composites dominated by interface layer

High Strength and Thermal Stability of Multilayered Cu/Al Composites Fabricated Through Accumulative Roll Bonding and Cryorolling

Design a Ti6Al4Vâ€“Ti43Al9V laminated composite with high strength and fracture toughness

A study on the microstructural evolution of copper/aluminum composite strips fabricated by micro flexible rolling

Study on microstructure evolution and fracture behavior of Al/Al/Cu multilayer composites

EFFECTS OF HOT-ROLLING PROCESSES ON THE FRACTURE BEHAVIORS AND MECHANICAL PROPERTIES OF 2009Al/SiCp METAL MATRIX COMPOSITES